Viewing all customer Discussions for:

39-032 EntryGard Dual Arm Operator

I need a crank and cover for a 1994 semco casement window. Can you help please

Truth EntryGard I have two sets of windows in need of complete operator replacement. These pictured are both marked with R(assuming right hand window if viewing from outside), as the Left operators are still installed (I will need to replace those as well). The long arm is marked 40754 and the sho ... (cont.)

Windows hinge on outside at left, so it appears that product number 39-031 are the ones that we need, but please confirm. Long arm measurement on your website is very helpful. Our arms measure 10 3/4" to the screw. Short arm is 4 7/16". We need 2 operators and 5 cranks.

What are the replacement parts? For left and right? The arm is 9".

Have 2 casement sash windows with Truth hardware. Operator on Right side is broken and I need replacement plus 3 sash locks. The photo is of the operational side but to show what we need. The other side that doesn't work has the little black part in the corner that seems to slide and isn't attach ... (cont.)

Need replacements 3 left and 3 right. The arm is 9.5 inches

Looking for replacement hardware for this Pozzi window. Need entire assembly please. Please advise if you can help.

Good morning, Please can you help me in finding the correct parts for the pin holding the bracket 20810 to the lower bracket that is screwed on the lower windows frame, as well the metal block bracket that holds the pin. Also if you would be so kind and inform me of the part number of the screws hol ... (cont.)

I am searching for these, I need 4 rights, 4 lefts and 8 new cranks and covers. Can you help me?

I need help figuring out which hardware to buy to fix my window can you help me?

I need a replacement for the opening hardware for the window in the attached picture. I have not been able to remove it yet. I'm hoping the pictures will be adequate for ordering the correct parts.Crestline Casement Window Hardware. Left hand open. House built in 1992.

Both the handle needs replaced and the gears in the dual arm operator are stripped. This is a Truth dual arm operator and I see part number 40471 on the metal hardware. So, what can I use to replace this?

31538A LEFT HAND ENTRYGUARD

The photos show the hardware on the left window of a pair. The hardware on the right window needs replacing.I am handy enough to do the work if I have the hardware. Aside from "Thermal Gard" on the crank, I don't see any identification info. (If you can identify these parts, I might buy both sides ... (cont.)

We need some replacement cranks for our KK windows. I think the numbers on the crank are 30810 and 6295P. It also has Entry Gard printed on it. I think we need about 5 cranks.

Hello Swisco,The Glass Guru of Carlsbad here. We need several of these for a customer, but we're going to start with one to try. EntryGuard by Truth, 4" straight arm, 9" long arm, 3 1/4" crooked arem, 5" bottom straight connector. Right side, including track on bottom of window.Can you find this, ... (cont.)

These are Pozzi Entry Guard windows from 1985. One window is a Casement and one is an awning. I'm thinking Part 39-032 for the casement window and part 39-070 for the awning window as the measurements match to those. Looks like the trim moulding has to come off in order to replace the parts. Will my ... (cont.)

I sent a previous email w/ o pics. Sorry. I ordered 2 39-035 thinking that this would also fit the Picture Window. My goof. The window is 65" tall x 18" wide. I'm helping my parents, can I return the extra 39-035 and place the order for this Crank and get refunded when u receive the Crank back? ... (cont.)

Not sure if this is considered left or right opening. # on gear plate is 40471. # on short arm is 20810. Only info on long arm is name "Entry Guard Truth", no #'s. Overall length is 13". Long arm 9". Short arm 4" (from hinge to end, not total length from gear. What is cost of replacement part? Will ... (cont.)

Entry Guard 20810 operator for a right side window. Arm is 8"