Viewing all customer Discussions for:

Door & Window

Good morning. I purchased part# 15-058. I have had a bit of difficulty installing this part. Do you have any "How To's" or youtube videos on how to install this specific part?? I have tried to google/youtube for this exact piece but could not find anything. Any help on how to install this would ... (cont.)

Stamped on channel: 35-9 DL5 CMC 9 We have 3 same windows, all showing same degradation at wheel near 'hook' (finger pointing to it at photo). Please advise regarding necessary part ID. Thank you for your assistance!

Looking to get a replacement multi-point mortise lock for my exterior patio door. Brand is unknown and the builder who supplied the door is not much help either unfortunately. If the mortise lock come with and entire door handle latch assembly, that would be fine also. The mortise lock doesn't lock ... (cont.)

Please advise and provide links to replacement parts for my non-tilt windows. There are no markings on my existing parts.The tube diameter is 3/8". It appears to me that I would need the following types:1) Spiral Balances, 3/8", 29" length, Non-tilt2) 1) Spiral Balances, 3/8", 31" length, Non-tiltAd ... (cont.)

I'm seeking a corner key and the measurement we need are 5/32'' x 1/8''. do you know the part number for that size?

Need replacement door handle for storm door. Don't have any info on name or numbers on handle or door. I already tried the 40-177 but it doesn't work on my door. These pics are of the front and back of the door.

I need two window balaces

Please give me your replacement part for this item. The measurement is about: 1/4-20" x 1/2" BUT the tip is thinner and not threaded.

Your dimensions are 1/2 in by one and a quarter inch I need one little narrower and thinner as this one fits in very tight and will not function properly up and down

We have a sliding glass door series 5800 and need a full handle replacement. This was likely new 2008-2009.

HiI have bought from you before and now in need to restock my suplyAre the door rayl replacement still availiabel? And wheels?Regards//Casper CV-INVEST

I'd like to find and purchase a locking handle for my Jeld Wen sliding patio door.It has an off-set latch mechanism and opens from the right panel - sliding to the left (as viewed from the outside).I believe I am looking for an "A" style with a keyed lock.Thank youMark

to open and close the window all u do is slide the lever from side 2 side to open and close window..the window goes out and back in 2 closeif u need pics i can get themDANIEL THANK U

Hi this is a PGT door roller for a screen door. PGT 82-00440-00070 impact door.. SGD 770. There is no numbering on the screen door.

The window part number is 2950 CJ AT or at least that is the number engraved at the end of the part. The metal length is 30" with a plastic insert on each end making the overall part 31". The windows are about 21 years old. I could find no description on the windows. The part is 5/8" x 1/2". ... (cont.)

I'm searching for replacement parts for these window track latches. I'm not sure of the correct nomenclature or description. Please refer to attached photos.

The numbers I see on metal look to be 20 3 The length of metal channel is closest to 20 7/8ths Not exactly 21, which is what I thought it would be based on stamp

Stamped on may part is 29B BSI GL, it is 29 inches by 1/2" x 1/2" with spring small nylon rope, (2) pulley and spring. Window is appx. 24 years old This looks like the correct part 29" Series 770 Balance Product Code: S770-29

I have 1 handle that has no splined female mount, is missing the set screw and the split pin.

I'm looking for this window balance, it is 22" x 3/8, but I can't find it with yellow tip.... I also need the other piece