Viewing all customer Discussions for:

Door & Window

Hi, I am looking for the side rollers for my sliding window. Unfortunately I don't know the manufacturer but I have a PAT.5.553.548 embossed in it

I'm looking for both left and right casement window operators, they both have number 20755. It looks like your part number 39-032 and 39-031 might be the correct replacements? Please confirm Thanks,

I have a hard time finding the right dimension for window slash as you put fractional number; I used a vernier and I do not know much of those inches. It would be much easier to write also milimeter, it avoids much calculation

Hi! I am looking to replace this 3 inch clip that holds the screen in place. Are you able to provide a part number based on the pictures provided? Thank you, Chris

26 1/2" 26 4 bsi tp

I have an ADW-8 sliding door. The lock broke on the inside and there appears to be no way to replace without disassembling the door. It is a series 311.

Per Milgard, the part number is BA0998BT, they also called it a 29-4 balancer I have included pictures of the balancer, shoe, etc Length of the metal balancer 28.5" Stamp on the balancer is 28 3 Pictures attached Thank you!

Hi, I am looking for a replacement for a left hand patio door interior handle replacement kit. Jeld Wen doesn't seem to sell them and wondering if your legacy handle would work for a left handle (opens from left to right). Thanks

Hi. I talked with a representative yesterday and am sending photos as discussed. I am looking for replacement ba lances for a window ELL-1 400/500 series. Your S770-34 matches it with the exception that the balance I have mounts with a clip instead of a screw. A pin is located in the second hole fro ... (cont.)

My part #opos 1525-5 your is 39-232 I think they look the same.

I am looking for a window lock replacement. The lever that turns the lock has came off. The make date of the window was 2009-2011. My builder sheet shows View Point Windows as the brand distributed by Norandex. A lot of the handles/levers are becoming more loose with wear so I am interested in m ... (cont.)

The replacements and my originals of this jalousie T Handles. Please note the 0n the phot next to the ruler that my original is 1/8 longer than your replacement and this difference is why my handle isn't able to spin (clear) on its turns. PS the handles with the Phillips screw is original and the f ... (cont.)

It looks like it's 2 5/8" long and about 11/20" width and maybe half an inch in depth. It was hard to measure though, so I'd like to be sure before I purchase something. Thank you

HelloCan you tell me what part I'd need to replace the broken tilt latch in the pictures? Thank youTony

Good Afternoon, I'm looking for a replacement for 60-C-11500-11 window operator for a customer of ours.

Hello, Somehow from going to bed and getting up our sliding door internal lock broke or was hung up. I needed a locksmith to come drill it out. It took 3 hours. I need the internal lock parts for this. I think by my original M/I Builders paperwork this is a Silverline 5800 Series. It has the d ... (cont.)

Hello! I recently placed an order but just cancelled it because now i'm uncertain if I ordered the correct coil. My window weighs 13 pounds and both left and right coils snapped. I've attached some pictures. I think only the coils need to be replaced. Any assistance is SO appreciated! I am a homeown ... (cont.)

Double spring is for 16 pound sash Single spoils for a 10 pound sash Will what you have work??

Submitting photos to double check my measurements. The part listed after the question about tube diameter I am not able to identify on existing hardware installed. Non-Tilt Window Balance 22" length & 3/8" diameter. Do I need anything other than the Balance? Part that is currently installed, tha ... (cont.)

I'm seeking for a replacement for a patio door handle.The space between the middle of the top & bottom screws is 5 ? and the midpoint of the screws that seem to connect with the in the latch parts is 2 ¾.Looks like the locking mechanism length is 3 1/6