Viewing all customer Discussions for:

Door & Window

I need to buy new window coil balance. 31" x 35" window. The area that the ciol goes is 18 1/2". The thing that holds the coil is 1 1/4". The stamp says 7K and the coil is 3/4" wide

Hi there,I'm looking for a window balance coil replacement. As seen in the attached picture, the broken coil shows number 3 stamped on it.Please advise if you have any available parts matching this coil. I guess it will be wise to replace both coils at same time, even the other one still works. Shou ... (cont.)

Does the In-Swinging Door Handle Set, 1-3/4" Product Code: 40-028 come in bronze?

What replacent roller assembly do I need for this door? The only marking on the door is the pic I sent saying it's a SGD-R35. Mfr code is Kinco LTD. Series is Mark ll,111,lV,V. MST is 16068. The door is a 95 inch door. I hope this info will you identify which roller assembly I need.This house was bu ... (cont.)

I have to replace my set of channel balances. They measure 37 inches long. Photos are attached . Please provide an estimate of cost to replace. I will do all work to install new.

I have a Pella storm door model 91022.331 with a left hand latch. The latch spring mechanism is defective in that it will not hold the door shut.

on a larson storm door serial number 024881u.111971104

Hello, I am looking to identify the right parts to replace a 27 4 EW CMC 10 - the string seems to be stuck somehow and I am too cautious to try and right it assuming the spring may release its tensions in one quick go. Any help is much appreciated - thank you!

Hello, I am looking for weatherstripping parts V130 and MV116 or equivalent,also sash balancers, can you help?

Hello, I am looking to identify the right parts to replace a 33 6 HW CMC 11 - there was also a 33 4 FW CMC 10 in the other side of the window but the mismatch of the second number (6-4) seems to be what may have caused the break on the 33 6 HW CMC 11 as I understand the second number to be the bala ... (cont.)

I'm looking for a Constant Force Balancer for a PGT SH5500 single hung window.

Need pivot rod for G A home single hung window.

its a masonite screen door I need a new roller

Hello, I'm missing two parts for an awning window and I am unsure what they are called in order to replace them. In the first photo the part missing is is the bottom piece that is circular and runs the bottom of the window, and attaches to the window crank. The second piece missing is the part in th ... (cont.)

My Pella screen strike measures 5/8". Do you have a Pella strike that is smaller than the 70-225? Thanks, SP

Trying to replace this part would like to get two

The brown handle broke off you can see the littletiny piece in picture four. The handle measures about 10 inches in length and 1 inch in width. The inside of house the handle is white. The outside of the house the handle is brown. The door handle inside says these numbers SGDH - 6 and underneath ... (cont.)

My wife was clean our windows and it broke. It appears one of the pins broke and on the same side the thing it attaches to(I think it's called the shoe?) Is broken too. And the pin on the opposite side is bent. Can you help me?

House was built in 2008 and window wont stay up. I am not sure of window manufacturer. I may need new shoes also? Can you help me identify these parts? Thank you

I have a 2015 Jeld-Wen sliding patio door that i broke the lock handle on. Will your" Sliding Door Latch Lever Kit Product Code: 82-107 work? Also in need of bottom door pile weather strip. What do you suggest? Thanks for your reply, Russ?