Viewing all customer Discussions for:

Door & Window

The door manufacturer is ESP of FLA. The door unit is 13-14 years old. The housing is 2 1/4" long, 1 1/2" high and 3/4" wide (at its widest point). The roller is 1 9/16" in diameter. I am in need of a pair of these rollers. Thank you

Need parts: It is a tilt single hung window. I could not find any technical information in the window. Thanks.

I am looking for a replacement seal for my front door threshold ! It looks like a upside down V with a 1/4 inch round gimp on one side

On the large part spring has number a big 7 then a small 23x onit. The small one has a big 7 and then a small. 37w believe to be TRACO WINDOWS. BRIGHTON GLASS

Do you have this lock and colors please. Cost?? This is not original color it was painted over by previous owner. Original was either brown or bronze Thank you

Hello, I need help figuring out which number of channel balances I need. They are 24" long and 1/2" wide. The markings on them are 2340, 2305, and 2230. I just don't know which of the many choices available I should select. Thank you, Magdalena

Operator pictured was purchased from Swisco within last 4 yrs. Have not identified a replacement in your on-line catalogue with same measurements. 39-329/30 appear to be closest. House directly on ocean. Salt spray degrades operators within 3 yrs On 3rd set of operators. Would be nice to find co ... (cont.)

Have a vinyl sliding glass door that needs to be adjusted and/or have door roller replaced. there are no adjusting screws on the bottom corner of the door, only two plastic caps on the inside face of door at the top frame of the door. Opened these and there are no mechanisms whatsoever inside the fr ... (cont.)

Do you guys carry these parts and if so how much?

looking for sash balancer matching to the picture attached. it is from a 35 year old Anderson double hung window. It has a number 11600-17 on it and a H24 623 10 88 code on it. Could you please let me know what matches to it? Thanks, Tom

truth made in china

Pls let me know if I can get this partThanksHaresh

The Folding Crank handle is originally for Anderson Window, part #2108 is on the inside of the handle

No markings... Trying to find this wheel assembly for a sliding glass door.

attachment holes on 3 inch center--only name found was on top of door handle plastic ---(international) ---handle length 7 inches patio door was installed in 1977

Please let me know what other photo angles or information I can provide.Measurements:casing: 150mm X 50mm X 25mmtwo hole base: 59mm X 22 mm, screw holes 7mmswivel arm: 69mm X 15mm, hole diameter 12mm.

I have non tilt window with mis-matched balances, Caldwell type (One 23-3, One 23-4 They are also different end guides). I noticed the rest of the house has BSI type. I replaced the dual pane glass in this window because of condensation. The window is now Heavier than before, about 28lbs. So, t ... (cont.)

When I try to lock the door and the hook touches the side of the re-sever the hook falls down. I bought a new one at Menards and the hook still falls down. Will your lock hook not drop down when you lock the door if it bumped.

Hello, I would like to buy window balancer for two windows. The picture of one of the window is in the attachment. The other window is just the same. The size of the window is 32*27 inches. The old balancer is 27 inches long. My questions are as following: 1.If all the balancers don't work, I need ... (cont.)

I.m Joseph. The coil balance is stamped S 361.No found in your catalogue. I need two. Thanks Hi. I'm Joseph. Coil balance stamped S 361. Need two/ Thanks