Viewing all customer Discussions for:

Door & Window

3/4 inch deep, 2 3/4 inch wide, 2 1/4 inch screw to screw. ?Tongue? that fits under window ledge when lever is closed is 1/4 inch. White metal with no name, just letters/numbers as shown on underneath photo. Help please! All I?ve found have a ?tongue? that juts out 3/8 inch which won?t fit under ... (cont.)

Hi, I recently had a window balance pop loose from the sash. I have Milgard, single hung, non-tilt windows. When I removed the balance I noticed that the top portion was damaged (parts of the catch area were chipped off and it was missing the spacer on one side). The top sash guide was also heavil ... (cont.)

Need two of these. Body is 12" long. Has the marking "11 5 Caldwell" on it

Hi,I appreciate your help replacing the wool pile in my Weathershield Patio door. I carefully measured and think that my wool pile (no center fin) is 7/32 x 7/32. Please let me know your thoughts on a match for me. Regards,Mike H.

I would like to replace a broken window pivot shoe. I've attached some pictures and the dimensions are approximately 30mm wide, 50mm tall and 15mm thick. Can you please help me identify this part? Thank you!

I know I am looking for a series 770 32" sash replacement. The attached photo is the number staled on the current part. I don't know what weight I am looking for and hope this photo helps. If not do I simply weigh the window and divid by 2. Assuming each takes half the weight. Also not sure option? ... (cont.)

Need replacement rollers for a SGD R20 73 x 80" aluminum patio door. Need two sets Four total. Thanks

the "T" dimension is approximately 17/64th" across the top of the "T". The bulb is heavily compressed but appears to be approximately 20/64" in diameter

Don?t know window make. Part shown with tape is broken and looking for replacement. Part shown holds window via pin and slides with the aid of attached spring which attached to the top of slide which is broken off Bottom of piece hold window via pin. Top (broken off) attaches to spring which when ... (cont.)

Only thing found on screen frame was 24x31 looks like there's another number but its faded I measured the screen corner blade width, the corner length and the thickness. Hopefully you have a recommendation and thank you The frame is 9/16×3/8

Would you be able to find this part or anything similar? Price?

Looks like 5/8 wide with an L shape brown or black plastic piece. Thank you, Jose

I believe I have an issue with my balance. I am not overly familiar with the naming convention with windows, so I am be using the wrong terminology. I am including some pictures of the issue. Please let me know if you need further details to diagnose the issue or the piece needed. ... (cont.)

I am looking for contoured plugs to apply over the screw holes in plastic window frame that holds the double glass in my two exterior doors. The doors are metal and the plastic frames squeeze the glass panes and the frame sides into the door by being screwed together with an applied sealer. I have c ... (cont.)

series 1400 mechanism to open and close

Any idea on which one I have. I have special ordered from local stores none of them work.

I have a 28 inch set of channnel balancers needed for our customer. It uses a different clip than normal and it fastens with a clip on the top. Thank you Mike

I have screens from 2003 and the manufacturer went bankrupt (Bonneville in 2009). I need replacement pins, but nothing matches the size pin I need. The inside screen frame hole is 3/16 inch wide, and the outside frame hole is 1/4 inch, or maybe 7/32. The problem is the inside (3/16) hole. The probl ... (cont.)

1 1/2 " tall 5/8" wide Top piece 1/2" tall round screw hole 3/4" from top Bottom section 1" tall from tapered tip to bottom of top section Says M513 on the back

I can't identify this part for our patio sliding door. It?s hopelessly jammed and need replacement. Please help. Thanks, Phil-