Viewing all customer Discussions for:

Door & Window

We just moved in to a new home. The windows are about 2 years old. The sticker says Silver Line product ID 50 series GL Actual size 60 x47 8002344228 They slide from left to right. I?m looking to replace a few locks. Can you identify the correct part for me?

We need the long arm operator Anderson window # 0338710. ......Is this the same as the 39-389??? Please....need ASAP......Thank you

can't find winged shoe as depicted in 1 and 2. On Top Shash guide I'm looking at 18-064 all measurements very close, but no sharp tooth on front. 18-009 not as good on screw holes, but has tooth. On what I call window spacer, can you give me a part number?

I do not have any information on the double pane pivot window; so I am hoping the picture will help to locate the bar I need. Thank you, Frank

I am ordering replacement balances, and I have done this before other windows. I am ordering series 350, items 2240 and 2640. My question is, I don't see any sash guides installed in my windows, should they be installed? Would they make the windows operate more smoothly? Thanks for your reply! Ca ... (cont.)

These fasteners are broken, I've glued a few together but all but a couple broke again. The door is not secure and cannot be locked reliably until these are replaced.

Hi! I am looking for replacements for 3 Caradco window operators. One opens to the right; two open to the left. The only parts I needs are the crank assemblies with the arm that connects to the window. The hinges and other parts are in good condition. Please let me know what further information you ... (cont.)

I need replacements for right and left hand latches. Here are photos and a drawing with measurements that are pretty accurate.My husband says the material is pot metal.Please let me know which replacement parts you have that I can purchase and what material it is.Thank you so much,Chris ... (cont.)

We have a broken glass in the lower sash window of our modular home. I do not see how to remove the sash from the frame. Can you give me some instructions. the window was in a modular home purchased in 1995.

We need 4 windows repaired. Replace damaged tension springs. We have another window that needs replacement.

This may not be original parts to the storm door as it was said to have come with the house. The window had a faint maker?s mark. Looks like the measurement between the top and bottom hole is 6?. The measurement between holes on the latch and lock are 1.75?. The outside is brass Which brand could th ... (cont.)

Need replacement parts, 28 " assembly for 31 lb window. Block/Tackle screw mount at the top. 1 1/4 inch shoe, 9/16 plain channel

hi i need help to identify the attached truth door keeper thanks

This is from a Ply Gem window installed new in 2010. There is a number inside the handle, OPO6-1520. The handle is 4-5/8 inches long. The spline itself has 12 teeth, it is 1/4 inch inside the teeth. The piece that fits over the spline has 10 teeth giving it room where the lock screw fits. It's a rig ... (cont.)

Our windows have wool pile that I am unable to remove. Do I have to take the window off the house in order to remove the pile?

We need a replacement part for our Window. Hard to find a tilt window latch for the Window. There is a 075 on the bottom side of the latch. Do you know where we can find the tilt latch. We purchased our WENCO windows a few years back and are in need of two tilt latch replacements ... (cont.)

Hello, looking for gasket similar to part# 58-135,3/16×3/8".looking for strp with 1/4"flat on bottom that fits into channel.please reply asap.thank you.

these are broken in one window. Window does not stay in the clips, clips remain in down position. What to order, and how to repair?

I need help identifying this vinyl glazing bead. We believe it is from an Atrium window. Thank you

Hi. I need right hand and left hand crank units . Total operating units . Thank you .