Viewing all customer Discussions for:

Door & Window

The locking mechanism was 3 point but I'd be happy just to get the main lock replaced.it says it was made in New Zealand. Any ideas?

I have an archaic model. I've seeing that the new replacement number is 81?258. I know that I need to remove the corner bracket from the old roller. What I need to know is does the new bracket or housing automatically come with the replacement roller? If not how do I order the replacement roller ... (cont.)

I need 2 complete storm door latch sets (Inner & outer ) Door # 121200948440002. If you send me an email address I can send you pictures. Thanks.Paul

I have seen several discussions with people asking to get replacement rollers for their Better Bilt windows. You always end up recommending part 87-181 which is the correct dimensions, but it has steels rollers. I spent considerable time a couple years ago filling and leveling the aluminum rails in ... (cont.)

the stamp on my balance is 25 5 JV CMC 2. Which # does that relate to? Thanks

Various numbers, one of being, 19 3 / 3.SI, PAClosest I see is S380, S385 but not sure. Please let me know ASAP.

Measured 9.5? on the long arm with #30470LH on back side.

The pivot lock shoe on one of my sash windows has broken. So far I have been unable to remove the window, which is the bottom one and pivots inwards. I believe that the mechanism is yours, though so far I have found no markings. The window was installed about 13 years ago. The measurements of the wi ... (cont.)

Not able to find any name or number, but I looked on the catalog and the closest part I could find was 18-176. The measurements on the top are 1 1/8 by 5/8 with a length of 1 1/4. These measurements are + and -.

Can you identify my operator?

Latch : there are 2 patent numbers on this piece - US Pat.5,620,213 and CDN Pat. 2,142,071 Handle : USA PAT no:6375332/CAN PAT no:2310998

Looking for item in attached picture. (Release latched for tilt in sash) they measure 3 1/2" long. A shy 1 1/4 wide. Screws holes about 2 1/4 on center. Color: Bronze

What size and type of spline should I used to rescreen my Andersen 4000 series storm door using a pet screen? I'm having trouble figuring out the size and type of spline to use. Thank you!

Hello, Having trouble finding proper coil balances for Simonton windows. Windows are standard 36"x60" windows marked: Simonton Window 9904161120, D0349 4/16/99, 2370629/01, UNIT: 35.5000 59.5000, G1 31.5625. 27.0625, OMSH. Old coil balances are marked 5.5#, 39" A PAT E523208, but measure ~64" l ... (cont.)

I am looking for a replacement part for my sliding screen patio door. I need the corner part as mine has broken where the wheel attaches at the joint. Was not sure what would be the correct replacement part, in metal.

Small metal piece broke off inside, affects turning

Hello I am Not having luck finding the replacement in the local stores, not sure of the brand, but the door thickness is 1 inch, the backspace is 5/16 the screws on the side (top one to the bottom one 7 inches apart and the mortise is 13 /16 wide, inside top to bottom are 7 1/4 inch apart. Outside b ... (cont.)

Hi, my window wouldn't stay up and I found your very useful videos and was able to determine that the right-side channel balance spring had detached from the clip, and to get it back on track, which fixed the problem. However, it feels like I have to be very gentle when opening or closing the window ... (cont.)

Just need (jamb side) latch,however if that can't be purchased separately need to know which set to order,via pic sent.. Larry

Could not find this window lock on your parts list I need about 4ea. I am in the process of replacing some channel balances and have a few of these that are broken. Thanks. Not sure the manufacturer of the wiondow but the lock is about 2.5" X 7/8"