Viewing all customer Discussions for:

Door & Window

This is a hurricane proof window that's 52" wide and 29" tall (just the window that slides up and down is 29" tall). The part number stamped on the broken channel balance is 29DS 48L. See attached photos. I need two since both sides are broken.

Hi, I need 2 21" replacement channel balances for my old Milgard windows. I attached pictures, with measurements. They are stamped 2040. I'm not sure which series (385?, 390?, 395?) to order. They all look very similar, but none exactly match the ones I have (shoe guide depth, top and sh ... (cont.)

The pivot bar on my 2014 tilt latch window is broken & Builder

It holds the top of the window in place

I see you have the 36-018D top latchs, 36-018C intermediate, but no bottom vent latches. I have Stanley roll out windows. The plastic latches have cracked. There are three separate window sections that roll out. The bottom plastic vent latches have broken. Please call me. Thanjs, Greg ... (cont.)

I need a Armaclad replacement Storm door closer - It would have to be heavy duty, black in color and appx 15"" in total length. The part number on it is #0301. Thanks - Jeff

Hello, Looking at item 70-009, can you tell me how long the thick part of the pin is (the 7/32" part)? I've bought some other pins and this 7/32" part was about 3/16" too long so when the pin is installed in the screen, and the pin is fully retracted it still sticks out of the screen too m ... (cont.)

Made by AW Hardware for Anderson Windows 25 years ago -- 1992. Note beveled angle of latch.

Wondering if you can help identify the part in the pictures. Its for a window screen. If not is there a recommended replacement part?

I have a Fleetwood Bounder motorhome. The sliding closet door rollers are broken. I haven't been able to find them as they are a smaller size than normal doors. I have attached a couple of pictures with dimensions. Any help would be appreciated.

Hi, This is the remaining piece of a pair of clip-like devices that hold my basement windows in place. I have been told that they are not made anymore and that I will have to get a machine shop to manufacture a new one. I am hoping you can steer me to something pre-made that will work. The wind ... (cont.)

Do you have a replacement window roller part # 87-147 with a double roller (wheels). Thx Al

I am looking for the spline to a screen door that resembles a forever door. I can not find the door manufacturer but was purchased at Home Depot. The channel is 5/16" wide and the old rigid spline was 13/32" in total width. I need 12 feet of material. What material do you have for this project? See ... (cont.)

The numbers are as follows: 30841L - on section of arm that attaches to gear an extender piece. 30843L - on large gear 30830 - on piece of metal that attaches to window crank. The part that is broken is the part that the crank attaches to. The openers seem to work fine with the exception of the cr ... (cont.)

To whom it may concern, I'm looking for the Right Handed Window Operator. I had bought the one in the pictures from Home Depot a couple of years ago but cannot find it now. The measurement between the two bottom screw holes is 1". The measurement between the hinge rivet and 3/8" hole is 2 5/8". ... (cont.)

sent 3 pictures but will send more in a separate email. lifter/ balancer/lifter 17" X 1/2" round. 1 is red tip 1 is blue? Spiral mechanized. note small snap in aluminum block appears to hold base of shown lifter against bottom of window, maybe to eliminate inserting a screw?? Question do I need t ... (cont.)

I'm looking to order 8 rods 24c &4 rods 21c please identify the rods

Need to replace about 8 of these. The stamped number does not quite match up with the ones on your website. Don't want to make a mistake so I thought I would check with you first. These are 1/2" channels, 5/8" deep. Just under 38" in length, clip end to clip end. Also, do you have some replacement e ... (cont.)

I need the aluminum counterbalance with spring, mine has a mark number 1610 Need two that size. The slide had a nylon upper part the fits into a pair of slots and a lower nylon part that has a pivot for pulleys.

Here is what I have. Any help would be greatly appreciated!!! I have a window counter balance that has gone bad. It says 34D BSI (I think that is what it says BSI). The roll formed metal is 1/2" x 1/2" x 34" in length. The I have from you is 9/16" x 9/16" x 34" and is much larger. I can send yo ... (cont.)