Viewing all customer Discussions for:

Door & Window

Not sure if the pictures were sent. I am in dire need of new balances on several windows. The metal portion of the balance measures 30" and is about 1/2" wide. The plastic top portion is very similar to part 19-005. It has a length of 1 1/8" and the wings measure out at 15/16'. The bottom shoe is ve ... (cont.)

This part goes in the side of the window and guides its movement and acts as a travel stop. There are two in each window.

1. I just received my order today. Thank you. 2. Problem: I noticed that the existing pivot shoe at window (Attached Photo: Pivot Shoe at Window) and the one I bought from Swisco 15-045 (Attached Photo: Pivot Shoe bought) do not have same size HOLE. Please see the attached pdf file for detail. ... (cont.)

Hi, I hope you can help me with the broken handle to the window, attached are some pictures of what it looks like. Please let me know if there is anything else you need. Best Linda

HI - Please help me choose which balances I need. They are all the same, and I need 8 of them. They are all 24" long by 1/2". The only identifying numbers I found are "2330", with an upside-down "R" next to that number, plus a tiny "B.S.I" next to the "R". On your site it looks like I need either th ... (cont.)

windows were purchased in 1984 Anderson Double Hung Markings are D31 8#31 3-85 bottom sash glass measures 22x28 I need 2 balance replacements

I have several MI Windows Series 3500 that need to have the balance springs replaced. Do you know where I can order parts or if I have to replace the entire window?

need to replace balance

What model sash spring ballancer do I need for Anderson window CIG -1 2-95.6

Need mortise lock for a Champion 6000 series sliding glass door

Hello. t appears I have made an error. My intent was to order a like-for-like replacement of two "Truth 31761" tandem rollers.However, the 81-018 that I received - while they do fit the mortise opening - are too shallow, and therefore, put the height adjusting screw below the door's access hole, a ... (cont.)

Need help determining what channel balance i need. The length is 29 inches measuring only the aluminum as described in your video. Just not sure of the end pieces. See the attached photos. Thank you, Deborah

Greetings, I currently have the rods in the images in my windows - one won't go up, the other won't stay up. The existing rods measure 27 1/2" from top to bottom of blue bushing. Can these be replaced with current models not having a plastic tube covering? Thanks! Bob A

Hi, I'm wondering if you can identify this weatherstripping. I have wood casement windows and this fits in the groove around them. House built in 1978.

I have purchased 79-127 and 79-097. Neither one are quite right. I have attached a photo of my hinge. Can you help me match it?

Which one do I need?

Please see the attached photo. Note that the trim, window stops, are off the window at the upper left and lower right of the window frame. I need to replace the trim/stops that have broken. To be sure that I have enough quanity and to address perhaps other windows I believe I need roughly 16 line ... (cont.)

Please help me identify this window balance. It is 29" long, 1/2" wide, and the spring is 16-1/4" long. Thank you, Yoel.

I have a 10 year old house with MW windows. They have channel balances with pivot shoes that are similar to the series 795 balances with the exception that the clip and shoes are different. I have attached pictures of a channel and a pivot shoe. The channel is approximately 1/2" wide, and the sh ... (cont.)

The only window identifier I can find was a paper glued to the top of window. Written in the exact order as below. "MI Windows & Doors 26211353.1 1650 Warranty information -Do not remove" Attached pictures are from a functioning window. The symptoms of the non functioning window. 1. The ... (cont.)