Viewing all customer Discussions for:

Door & Window

Hi I need to buy a channel balance for MW window. Vent size 27"x18". Part length 15". thickness 1/2". (14 4 dp caldwell is printed on the part) Thanks for your help. Abe

I have this on my storm door holding glass in. I am trying to find replacement strips. Thanks.

I've attached pictures with measurements. The window is in a new home purchase and I cannot find the window manufacturers name. Do you have a replacement latch that will work?

I have a removed 28 inch window channel balance. It has a stamp on it 27B. It does NOT have shoes on either end. The bottom window tilts in to remove this channel balance. This is a single hung window. The depth of the removed channel balance is 1/2 inch.I bought a replacement channel balance but it ... (cont.)

Based on the dimensions shown, I believe that I am looking for the 5/8" top sash guide (18-009). My part has only one screw hole (the 3/16") and has a part number H-719. Can you confirm that I have the right Top Sash Guide?

The screen corner measures 5/16 X 3/4 as shown for your product 95-031. The 5/16" X 3/4" I purchased at the hardware store, the arms that slipped into the aluminum side are bigger then the slot in the aluminum. The dimension of the slide in part of the corner appear to be 1/4" X 1/2" X 1 1/8". Can y ... (cont.)

aluminum siding door locking mechanicnizm..acorn series 1200 #8882

the 1 x 1 black latch (clip on) to attach window to opening bars for Alside window

Hello, My window balance is stamped 16A, does that mean the lowest 'weight' for sash of 5-8 lbs corresponding to a 1610? Thanks, in advance. PS I've already selected the channel rod 380 with the appropriate dimensions, just need a little help with the weight I should use. Ruta

I am trying to identify and purchase the replacement parts for the Atrium Window Non-Tilt Block and Tackle Channel balance the code on the existing is: 34-5 EA2 CMC 12

Single Hung NON-tilt window. Balance on either side broken, or the catch to hold the balance in place is broken. the window will not stay up when opened. Do you have repair/replacement parts?

Hi! I purchased the replacement part pivot bar #26-336 for my window, the tip of that bar doesn't fit the existing pivot shoe; I am looking to replace the existing pivot shoe since it looks like the correct pivot bar for this window is no longer being sold. Could you please direct me to which is the ... (cont.)

Hi, I'm looking for something like this CONCEALED INTERNAL TILT-IN LATCH, WIDE - DISCONTINUED Are these available anywhere? Thanks

"28 4 FP Caldwell" is the print on the metal bar. It's a none tilt window and the metal bar measures almost 29". 1/2" channel width. Please advise on what part to order. Thank you!

Hi,I'm having trouble identifying the window manufacturer. I see no name or anything printed anywhere. I need the side tension springs for this type of window. Any idea who made the window? Thank you very much. Tim K

Caradco window. I sent pic of left inside operating. I sent pic of Right inside crank mechanism. The crank mechanism that the inside lever/handle attaches to will screw itself out to the inside as it appears to be broken where it attaches to the mechanism under the wood that hte screen sets in ... (cont.)

Hi, I ordered and received a 91-140 slide bolt kit. It is exactly the correct one except the tip that locks the window in place, is 3/16" wide. My that broke off, are only 1/8 wide. the new ones are to "fat" to fit properly in the slot that keeps the window from moving up and down.. Any help would b ... (cont.)

I have care free windows with 3/8"x29" spiral balance with red end. It has the pictured pivot shoe which I don't see on your page. So can you help me find what I need Thanks Bill

I have what I believe is an older Emco storm door that I need window latches for. I'm sending a photo and drawing. I ordered from you before but the ones I ordered were a tad to thick,they were the 91-063 & 91-064.I didn't send a photo before so may I'll get it right this time.Thanks,Steve ... (cont.)

I need replacement roller assembly for herculite k sliding door 3/16 tempered. This assembly has small prongs that slide down.