Viewing all customer Discussions for:

Door & Window

I bought 20 of these back in 2011 and used all but 4 of them on my Arrow Vinyl windows. I am replacing the balances again and was doing it the same way I believe I replaced them last time. I watched https://www.youtube.com/watch?v=bwpWv3xpZkA. I duplicated the process and even replaced the pivot bar ... (cont.)

Have an old window lock needing replaced

I'm looking to order these in black or dark bronze... can you help?

Only markings I can find are 090 & Pat. #5.671.958

I need the whole assembly with keeper. Any ??

Hi - I need some help with quite a few parts 'Firstly I am looking for about 6 take out clips - I assume they are pretty standard ? Then, I need quite a few channel guides the interior width looks like 7/8 inch - here are some pictures - do you think you can help me locate these ? Some pictu ... (cont.)

I need the coil that goes behind the plastic piece shown in the picture.

Hello, The handle that fits my sliding glass door broke. The only information I can see on it is: 3 3/4" (if my measurement is correct) between the screw holes, the numbers 124 or I24 and L120. Do you have a replacement part for this? The one I saw on the website show 3 1/2" and I may have measur ... (cont.)

Hello Swisco I have sash window. aluminium frame with double galzing glass installed (this is sound-prof double glass). The actual window can be moved freely without the spring balance installed. It is heavy, but I still need to weigh it (in the next few days, as it is installed about an hour's t ... (cont.)

33 lb BFS window sash. The channels are B.S.I. 27D and measure 9/16 wide and 9/16 wide - 27" long. Has the 4610108 patent mark on the bottom connector. this connector mates to the bottom "hook" on the window sash. Need replacement pulleys and bottom connectors - and the channel itself. ... (cont.)

I have a BetterBilt West Series 350/35T Single Hung window, and what looks like the coil balance has broken. I have attached pictures of the top and bottom plastic pieces, as well as the whole assembly. You can see in the bottom guide the broken coil, coiled up above it. What part do I need to fi ... (cont.)

this is a channel / sash balance for a single hung Windowmaster vinyl window. it's 16 inches long and has the following markings 1530 BSL mm.

I'm looking to replace some damaged vinyl glazing bead on my windows. They have a Ga on the locking mechanism. I ordered the 55-180 and the biggest side that is exposed is too small at 7/16". As you can see in the measurements I need it to be 9/16". Do you have anything that will work? ... (cont.)

Hi I am looking at replacing these sash units because my windows are all falling down when I try to open them, and I cannot keep them open on their own. Wondering if you can help me with replacement parts and a how to, for replacing these?

Can you tell me if you sell replacements for the handle in the photo? It could be "both parts" which would be the mounting block AND the swivering handle/latch or just the swiveling handle/latch, which is an angled "L" shape. If you do have these, are they metal or plastic (my windows include ... (cont.)

The current doors were built in 1975. I am looking for 16 METAL rollers with the following dimensions: Largest Diameter 1-1/4" Groove Diameter 7/8" Width 3/8" Hole 19/64" (I can take a 1/4" hole and drill it out bigger to use the current center shaft, that is no issue) Do you have a match fo ... (cont.)

This is a channel balance for a Gapco non-tilt window. There is a number stamped on the balance b3340

It said that it is made in new Zealand and there are no part numbers on it.

I need a left and right side, 2 sets of them. I changed the color of the windows.

I am trying to replace (8) pivot lock shoes which have a curved C on top that attaches directly to the side of each window spring. I have enclosed (2) photos.