Viewing all customer Discussions for:

Door & Window

Hi, I'm looking for snap in glazing for Danvid windows. See attached photos. thanks.

Im trying to determine the correct replacement part for a window balance installed in a Milgard Window. The stamp on the current balance is " 26 4 JO Caldwell"

Enclosed is an image that shows the problem I am having with my window. I have a pair of single hung windows like the image on the left. They were put in by the developer of my 10-year-old condo and I do not know where they came from. There are no identifiers on the windows. One window works ... (cont.)

Looking for the window balancers fro this Traco window. I'm hoping you can help. Please let me know if you need any addition information. Thanks!

The handle on my storm door needs to be replaced. It was listed as the JD handle in black. I would ideally like to replace all the hardware I have pictured, however I mostly need the interior and exterior door handles. They do not always operate well and I cannot open the door. I will also a ... (cont.)

I have a CertainTeed bay window that is about 12 years old. It consists of 4 window panels joined together. The joining screws are covered with small plastic plugs that are about 7/16 inch across and plug an opening about 3/8 of an inch. My two 10 month old puppies decided it would be fun to pu ... (cont.)

I need to find the correct keeper for this door -thx!!

Need 2 sets non tilt 23inches long 1/2 " wide numbers on balance are 22-2. J

I believe I need a 31" series 750 channel balance 30 HD (which is presently out of stock). From the attached pictures, can you tell if I am correct? I do notice that the shoe which remains in the vinyl jamb liner looks a bit different than what I see in the part offered. Also, would there be a vide ... (cont.)

Sticker on storm door for Pella lock Warranty Reg # 90566 321 0806324. This is all I saw, can you help?

The locking part of this handle has been missing since I bought the house. Can't find a new one. Not many numbers on the door or handle the only part number I see is the sgd-30 on the gold sticker. Any help will be appreciated

I ordered part 82-211. Mortise latch & keeper 3/4 wide. It's the exact size of the frame. Need something just a tad smaller. Spoke to your tech. Recommends I send pictures. Said someone will try to locate the correct size. Please help!! Desperate.

The lock on our Anderson sliding glass basement door spins freely and thus needs replacing. I am attaching three photos (edge and both sides) that are hopefully sufficient for identifying the right model. The lock is on the left side if you are facing it with the key from outside. ... (cont.)

Door at our church needs new Hinge I have no information on the door.lower hinge has two screws in upright jamb and two in threshold at a 45 deg angle. upper hinge has two screws in the header of the door

Don t know how to remove shoes from track. Need instructions as well as parts. I hope this is enough info. Contractor installed Windows. Home built in 1995.

I believe this would be a match for what I need, it would be nice if it were to have a manual thumb lock. Does it have lock? Or is there another item that I am missing?

Window weight is approximately 18 lbs Window believed to be Kinco 1988 Jacksonville FL. Only visible number is 28 3 F H Please help with channel balance part number and plastic clip

I have a cabin, circa 1976ish. My patio slider doors need roller assembly replacements. They are a single roller assembly. The stamp on the roller is. Product of Del Mar Eng Co Long Beach Cal Pat 3 670 357 (as best as I can tell) The roller has a hook tab above the adjustment screw. The ... (cont.)

Hi - The part shown in the picture broke and my window will not open. The same part on the other side of the window looks bad as well. Any suggestions on fixing this? Thanks!

POSSIBLY AMERICAN CRAFTSMAN AWNING WINDOW