Viewing all customer Discussions for:

Door & Window

I think I have identified the correct spiral balance I need. S900-23 (Red tip) but I can't seem to find a pivot shoe that exactly matches the look of the ones I need to replace. The dimension of your 15-046 match my dimensions so I am guessing these will work. Can you take a look at the pictur ... (cont.)

I need to replace the channel balances in a window 51"x 32". The markings on the channel balance is 29 9 HX CMC. Do you have a channel balance that I could use to replace mine? I have attached photos.

Hello, I am looking to order new window balances and want to make sure I select the right one. The numbers/letters I see on my old one are 2740, EH, B.S.I. Thanks, Tony

Hello, I wrote in a few months ago but didn't have enough info for you to help ID my parts. I will post the same photos again this time. I did find out that the windows were X-ACT replacement windows 1450 Series by a company called MI Home product. Hopefully that will help. Thanks much Richar ... (cont.)

70-205

The last picture is what I believe to be the problem. Looks like black roller is tilted and string is wedged.

Hi, I ordered 4) 84016 screen door rollers (order # 729798) and the wheel

In the picture on your website it only shows the lock. There is a second piece that the latch of the lock slides into. It goes on the other sash of the window. Is that part included with this lock? If not, what is the part number so I can purchase it?

Please tell me what type of snap in glazing I need to buy to replace the one pictured here.

1" and 1/8" wide 3/4" deep. 2" height Hi, I need two of these boots for 1 tilt window panel. Can you advise? I recently bought two spirals from you but now realized I need boots. These photos of of the boot for the other window panel that doesn't need work.

I have some top corners 95-206 but the bottom portion does not have the nub portion. Is it the 95-205 that is used at the bottom?

I have a 6 inch case ant operator that has broken. The cause is metal fatigue of the arm. However, I have not been able to identify the manufacturing company. I see no place to add a picture so I will email you. I have a contract to sell my home but I need a replacement part asap. Thank you This par ... (cont.)

I need to identify this glazing bead. Both pictures are the same one.

I can see the numbers (33 5) which from I assume is 3350 from your selection. the length of the metal is 34 inches. I need help with the correct ends. Nelson

the inside and outside plate is 7" in. the door plate were the latches come out and dead bold is 7 1/2" in. long. the door thickness is 1" . the tumbler has a key lock inside and out side. I never got the tumbler keys when I bought this house. do you sell just a tumbler and keys for this model? I ... (cont.)

These are plastic parts located on either side of window inside the window track. They hold the window to the spring. Without these parts, the window spring does not pull the window up. frank

I did not remove the broken part but I have this information. Andersen double hung window built in 1989. cig 2.2-89 daylight glass size of upper and lower sash is 28 3/8" X 13 7/8".

I need help finding a 2-1/2" pivot bar that matches the one in the photos. I believe it to be 3/8" thick. Sorry but please note that the ruler is in tenths of an inch. There is a number on the bar (8257 2) this is on the right hand bar and I need the left hand one. Thanks for any help you may ... (cont.)

I hope that you can help me find replacement wheel assemblies for my patio sliding doors. The doors are made of wood and quite heavy so the wheels need to be metal. The dimensions of the assemblies are 2.125" x 1.125" x .5" and the wheels are 1" x .25" w. I need 4 assemblies.

I need to replace the lock as when I took it off the plastic item was cracked in half. It was loose and I was going to add wood filler, but it won't help if it's broken. I don't want a keyed lock. June Rubicuski