Viewing all customer Discussions for:

Door & Window

We ordered 81-168 Tandem Roller Assembly, SS Wheels, but they are too wide. We need them to fit large Fleetwood sliding doors manufactured in 1983. The channel width is about 5/8". Do you have such units?

I need a quote for two replacement non-tilt channel springs see attached. The marking on the channels is not readable. Although I do not know the series I need the replacements would have the following: Top = 19-005, Bottom = 15-002, Length = 30", Window Weight Range = 16 to 23 lbs. ... (cont.)

Hi, I need to replace the channel balances in a whole house. However, I don't know which ones I need. It is labeled 940, has the 19-002 type top & the 15-003 bottom 21". Please help!

I need three white vinyl strips for Viking windows. two strips: 34" x 5/8" that touch the glass one strip: 37 to 38" x 5/8" that touch the glass I'm attaching a couple pictures. A hail storm put holes in them. The part of the seal that you can see is 5/8" that touch the window. It looks ... (cont.)

How can you tell if a spirial balance is broken or may have just slipped off? I have two larger windows that have the same problem. It looks like the clasp came loose from the window frame. I inspected working windows and I can see that the clasp clips onto the bottom of the window frame. I rece ... (cont.)

Hi I have and old window 2

I have window screens on a (Palm Harbor) manufactured home. The opening in the aluminum frame components measures 1/4" X 3/8". Will your straight cut plastic corner, #95-112 fit?

Not sure what type window no markings. But might be Marvin long arm is 9.5 in short arm with angle a is about 4.5 in I need operator on bay window that when u r standing in house opens from right to left

do you have the part for a peachtree glass sliding door roller assembly that has the part number 7116H-5 on it ... do you have a part that would match ... very heavy door

Please help me identify the correct snapin window glazing. See attach for details.

Hi, I am re-modelling a home, with Anderson windows purchased likely 10+ years ago. The plastic clasp at the end of the shaft has broken so the window will not open and close (though the cog mechanism is working fine). do I need to purchase a new entire straight arm operator, or is it possible just ... (cont.)

Nuair window, do you carry this part? I need 2

Please see the attachment lock photo. Do you have this in stock?

Looking to replace two right-hand operator units and two left-hand units with the c portion of the arm being 4-7/16ths. What is the correct part number for ordering same. These windows are 20+ years old. Thank you.

the part found in the images holds part # 26-056 found on your website, which is 2 3/4 pivot bar, trocal. there is no other way to secure the pivot bar into this window without the part found in my pictures.

The doors are from about 1980 or so. The length measures 5 inches wide. The bars are about 3/4 of an inch wide. The nylon wheel size 1-11/16. I can get just the wheel but looking for the entire part. It's made of aluminum. The extra part is what makes the assembly go up and down with a screw. The do ... (cont.)

I was told these are pivot bars. I see one is broken off and a couple of others are not inserted onto the window at the bottom. Thus, when the window is raised, the pivot bar remains in the lowered position and the window drops back down. I cannot identify the manufacturer of the windows. I had ... (cont.)

Your 40-150 looks like a winner, can you confirm?

We can't slide up some of our windows. There is some kind of plastic spring device that is broken. How can we replace this. The windows are made by Alcan. They are in good shape except for this.

Inswing patio door. The only logo I can find says, "The Aluminum Door." We have tried the generic replacement from Home Depot, but it was too small. Help! Here is what I can read from the bottom right corner of the glass: CFR-1201 SGCC-598 BS (or B5, can't tell) 6206A 1984