Viewing all customer Discussions for:

Door & Window

OK Folks, I looked on your website but never found this one; sorry but I didn't get measurements but many part numbers are visible. The number 30472 RH is found on one of the arms and 20755 is found on another arm. Please let me know if you have these- I need 2 RH and 1 LH Thank you very much!! ... (cont.)

Trying to repair my Mom's window. I had my wife send you a few pictures of the parts that I need to complete job. series is nc 1500/1600, I have more info off window tag if you need it. I think I need the pivot shoe 15-046, but part 15-015 looks close also. The spiral balance seems to be good, b ... (cont.)

Hi, I was wondering if you could direct me to the proper replacement part for my sliding window. The number on the channel are 32 5 BW CMC 2 the metal channel is 33" the plastic thing on the bottom looks like 15-004 but is 1 1/8" Thank you

1" nylon roller in nylon holder bracket. part failed after about 6 weeks. Part now tracks sideways or tilted due to too flexible bracket holding wheel. Have tried manufacture and they have no contact number for part or warranty replacement. Is there a replacement or another part that has metal brack ... (cont.)

I also have the #26-375 pivet bar. I have 2 to install. Is there a video such as the ones above to show how to do this? I just had the glass replaced and it looks like I have to redo the glass to get the pivet bars in place. Any help with this will do. Also a Better-Built brand window. Thanks ... (cont.)

The lock pictured is broken and needs to be replace. Need 7 for right side of window and 7 for the left side

I need replacement parts for the Florida Extruders International Inc. Milestone single hung windows. Any ideas?

I need 2 of the OPPOSITE HAND handles than those in the pictures. The base looks very much like 38-064. HOWEVER, notice the strike in the pictures. The picture does not seem to match the strikes that match up with 38-064. Would you please give me a part number for the OPPOSITE HAND of the the ... (cont.)

Could use some help Identifying the roller hardware in the bottom of the door. Also any suggestions on who may have done the 3 session room install. If they are still in business I would hire them to restore all the rollers and seals.

I am President of an HOA in Peoria AZ in a subdivision built by KB Homes and they installed ALENCO windows. 10-15 years later we have many homeowners whose windows stick or don't stay or are coming out of their tracks. I would like to order: 24 units or 12 sets of 24-40 4 units or 2 sets of 2 ... (cont.)

Hello, i was wondering if you could help out with something here.. I am trying to find the same balcony handle that got broken in my condo. Here are the photo of it and it sure looks like the one that you have, Surface Mount Handle Set, 6-9/16" Do you think, looking at my photos that i am sendi ... (cont.)

Please advise if you have this piece available, if so how soon you can send it to Moreno Valley,

I am in need of some pivot bars like the one I pictured above,once I find some of these I will also purchase more parts I need to fix my windows , thanks Larry

the top is a 19-005 but the shoe measurements are different than the 15-004 or 15-005

Looking for four [4] side load balances. they actually measure 30" long from tip to tip, including plastic, 29" not including plastic. Please include {4} take out clips 16-002

Hi, I have IWC windows and patio doors. Window has weep hole covers and there is none for patio doors. the window weep hole cover is not closed fully and hence i see bugs using the space to invade inside. I need help to find the right weep hole cover for both my window and patio door. apprecia ... (cont.)

Please see the attached pics so you can help finding this part

I have a broken window latch that I cannot identify. I cannot find any markings on the windows or frame. Cheap single pane (pain) windows with broken latches. I have two of them. The separation between the screws is 1.5 inches. I have not found any latch with this spacing. The latch is spring loaded ... (cont.)

I'm ordering 88-013 and 82-043 in white, but I also need 4 new white screws to go with them. My original screws are 2 1/8" end to end, but are stone colored, matching the old hardware. From my research, I believe the screws to be 10-32 x 2-1/8. Do you have these screws in stock or do they come with ... (cont.)

does this door pull come with the key lock