Viewing all customer Discussions for:

Door & Window

Hi I have a PPG Hercolite.K can2-12.1 843791 and I would like to buy a key entry handle for the outside so I can access my home from the back of my house

I

I am looking for replacement plunger pins for our storm windows. They are in the form of a tee however. The plunger had a hole in the middle of it where the "handle" part come out. The house was built in the mid 80's. I don't know the brand. Do you have anything like that or know someone that d ... (cont.)

I need to replace my Channel balance and need to make sure I get the one with the correct ends. I have attached pictures of each end. On the channel itself, it has the number 2840 DL listed. Can you please help me get the right channel balance? Thanks Dan

numbers found on anderson window 11600-2 156 5#23 3-80 any ideas on which would match this 1980 manufactured windows

My window crank has completely worn out. The part number is 0P05-7532-00. numbers below that are: 10-07-05 and 69804 Can you help me with a replacement? Do you have a sales location near Oakland? Thanking you in advance for your help.

I bought your part #84-096 to fit the door corner of my slide screen door. See the picture for the details. I have one like your #84-108 but does not slot in. My door corner has a closed half circle at both sides of the middle solid piece. So # 84-096 that I cannot find at local store. ... (cont.)

I am working on a home built in 1954. I believe these are the original patio doors installed in the home. The owner wants to put a handle on the opposite door. I need to find one that looks like this. Thanks,

I was wandering if you have pivot shoe that is the same dimensions as the above with a brake.. I need 10 of them...Thanks Barry

Looking for match-- Pella storm door mortise handle set--identical to your product code 40-193 except: my end piece is identical to 40-193 at 7 3/4 by 13/16 inches. The other parts do not match; the piece marked 8 1/4 -- mine is 7 7/16. The hole spacing on 40-193 is 7 14--mine is 6 11/16. ... (cont.)

See attached photo of inside view. Need both inside and outside.

Can you help identify this door latch?

Hi, I order your 39-091 and 39-092 but I am missing the bottom with the screws to screw the operator on. Please see picture attached. I am not sure what is the part number to order? Thanks

We have Patriot single-hung tilt-in windows. The window has a balance on each side; each balance is attached via a thin cord to a screw up near the very top. The problem is that we have several windows where the balance has disconnected from the window on one side. How can we go about reattaching ... (cont.)

Hello, I need to replace several balances and tops. I will ask in 2 questions as I cannot attach enough photos. First is the top. Can you tell me which model number this is?

I am in need of replace my glazing bead on our sliding door. The larger side is 3/4" and the small side is 1/4' I'm not sure what size I will need. Thank you.

metal part is 24 inches long. In window 30x30

your code 26-394 look close my hardware PAT NO. 5,165,737 holes are 1 1/4" apart latch is 2 1/2" long latch is 14/16 wide

I need to find a replacement channel balance; the spring broke when we were raising the window. We were able to remove the balance.

I am looking for four patio door rollers for my wood frame, screen door. (It only uses two, but if I can find replacements, I'll get some spares!) Here are the parameters: My space into which they go is 5/8" wide, 1 1/8" deep, and 2" Long. The current rollers have a 7/8" concave wheel. The ... (cont.)