Viewing all customer Discussions for:

Door & Window

Please identify the balance needed. I will need to replace both sides. The measurements are 37" long with a 1/2" width. Pictures are attached. Please respond.

Trying to find replacement window balances. This one is from the left side looking outside towards the window. I also have a right side needed. I need both for 3 windows. Window is about 40+ years old. Double hung window. Box is approx. 6-3/8" by 2-3/4"

I HAVE A RIGHT BROKEN LATCH THAT I BELIEVE IS A SERIES 544/585 DH-R30 WINDOW. IT IS 2 INCHES LONG BY 3/4 INCH WIDE.

Please help me ID this balance, thanks

After much correspondence, #82-106 works perfectly. Thank you swisco for your continuous email updates on finding a solution for our issue.

Hi, I have a bank of old jalousies that are perfect for a three season porch that i want to keep. Over the years, some of the screen/storm clips have been lost, and I have had no luck finding replacements.

Truth crank for weathershield wood windows. House built 2000. I will send 2 more snaps with measurements

I have a 8 ft wide sliding patio door. Each door is 48". One of the rollers went bad. Am looking for replacements. Have attached pics of the rollers as I have not been able to locate. Your help is appreciated.

Hi ... I have 3 small custom Jeld-wen clerestory windows that I would like to reach (open and close) with a pole. I need an articulated connection because the window crank splines point up and windows are 10" from the floor. The cranks that came with the windows are : TRUTH 40984 which seems to ... (cont.)

I previously ordered part number 39-220 the body was identical to what I have the the arm was different

23 inch (1/2 inch) Side Load Single Hung Balance Springs. The Balance Springs are stamped 2220v. I think I need Series 380 or 385 but I cannot tell the difference. Pictures are attached. I also need Top Sash Guide. Picture are enclosed. I cannot find anything to match. Do you have any ... (cont.)

Hello, I am looking for a constant force counter balance spring or springs that will support a sign board of approx. 25#. The travel for this support needs to be 30 inches min. I could use more than one spring in my design. thanks, Bob

Will part number: Pivot Bar Housing, Upper Sash Product Code: 26-399 Fit in an American Craftsman DH 4000 upper sash? Thanks. Bill

I recently ordered replacement Anderson Straight Arm Operator, 9 3/8" Arm kits for left and right. We received the kits and the mechanism that is mounted on the Window sill is wider than the original one we have. Our present one has 3 4/16" distance between the two screw holes....the one we receiv ... (cont.)

Just wanted to thank you for your wonderful service! We ordered replacement latches for our windows. They were delivered quickly, fit perfectly and the whole process was pain free. We will be recommending SWISCO without hesitation!! SWISCO is unexpected oasis in this world of companies that couldn't ... (cont.)

Stamp:3340 Length 34" I mistakenly ordered S390-34 34" Series 390 Channel Balance and after looking more closely at the pictures it looks like one of my ends is slightly different. Please let me know if you find a replacement part. Thanks

Need to replace the rubber seal on a couple of storm doors. It's got a triangle on one side at the top - 1/8" wide, and is about 9/16" wide. It looks to me like the Larsen Door Bottom Replacement Insert Product Code: 58-149 might work, depending on the measurement of the V-shape shown on your web pa ... (cont.)

I purchased this replacement set but it is too long. Actual measurements of latches I am replacing are: 3" long by 1 1/18 wide. Any suggestions?

Hi, I want to replace the nylon plunger pin on my Integrity screens with a metal type. The measurement is 1 1/2" long. The shaft is 5/32" diameter near the head, 3/32" diameter at the narrow part of the shaft and steps up to 1/8" diameter where it inserts into window channel. what would be ... (cont.)