Viewing all customer Discussions for:

Door & Window

I am looking for pile weatherstripping which appears to be the following: base width 3/16 inch height 5/16 center fin color white Can you please let me know which product would be a replacement?

I have one that is stamped "A 3 19 573". Can you help with this part number? THANK YOU!

Replacement for permashield narroline window. Measures 6 1/2 by 2 3/4 by 1/2. Markings show 11600-17 and E91 9 27 5 84

Hi, I have several Andersen operators that have failed over the years and was looking online for replacements. I was almost ready to order from "the other guys" but stumbled across your site. Most of the failures appear to be the retainer breaking or wearing out that holds the worm gear. Just ... (cont.)

looked for like an hour --- no part numbers on any frame, glass, or any other part front or back. These are (I suspect) pressure shoes, they attach to the frame with an actual sprint , like 30" in length. The part that the spring attached to on the shoe is sheared off. I have several double hung ... (cont.)

Door approx 28-30 years old. Inside handle broke. Need the metal piece that the handle attaches to. Screw to screw measures 3-1/2 inches. Door thickness when measured facing the edge when it is open is 1-1/2 inches. Is your product code 82-055 the correct item replacement because the descript ... (cont.)

I can't seem to match up my sash balance to the parts you sell online. From what i can make out i can see the following items marekd on the sash balance: 600-17 and BL6 10#31 11 84 You can see these on the pictures i attached. Please help me figure out which part i need to order. Thanks ... (cont.)

I'd like to know if your Product Code: 39-031 will directly replace my window crank I believe to be a Truth mechanisms: 30740 L.H w/ short arm 30636/20544 and 30472 R.H w/ short arm 30842R/20810.

Hope you can help me with this hardware. TRACO window, Lower Sash balances and then also 2 sash tilt locks. See attached pictures. Thank you. Denny

Measurements: Top - 1" by 1 1/8" Top to bottom of first box - 5/8" Top to bottom of second box - 1 1/8" Total length - 1 5/8" Bottom width - 5/8 Bottom of first box on backside, 3/8" from edge that goes to angle. Appears that there was a tang that held it in place, in the top of the window, ... (cont.)

Roller dia 1". Height 3-3/8" Width 1-1/16; thickness 7/16" I am looking a metal wheel or nylon will be Ok Thx Mike

Your pivot pit, product code 26-402, is very close to those on my Hurd windows. Do you have any feedback as to whether they fit on a Hurd, manufacture date around 2001? Thank you for your help.

I have casement windows manufactured by MI Windows & Doors. The series # is 1470. Will any of your products replace the operator mounted on the left-hand side of the window?

I have a home built in the late 1930s with Hope's window operators on steel casement windows. Several are not working and disassembly indicates the arm gear is worn down to to lack of lubrication and window sticking. Is it possible to replace the arms? Is it possible to buy replacement operators? I ... (cont.)

We need about 8-12 pivot bars for our slider windows...the overall dimension is 2 1/2", the screw whole placement is at 1 3/8" & 2". There are two barb like bars comming out of the right & left side 7/16" down from the main rotating bars. Bars have 4 circles stamped into the bars in between the scre ... (cont.)

in my Anderson window was a sash balance with the following markings: BL8 10# 31 85. What replacement sash balance should i use/ Joe

I am missing the small WHITE METAL part on the frame which the "tongue of the latch" goes into? Size is approximately 2 9/16th x 1/4" small but necessary to lock our home up!?!?!?!?! We bought our home last October AS IS so I am doing lost of small silly repairs like this cause the builder was in ... (cont.)

I have a non-tilt window whose channel supports are in need of replacement. I looked up the id marking online which brought me to your website. However, I cannot figure out what replacement part to order. I've attached pictures in the hopes you can guide me on what to order and how to install. ... (cont.)

somehow the homeowner lost out the "geared bushings" of 3 of his operators! Here is pic. Looks pretty standard. Thanks, Randy

I need to replace several broken coil balances in Thermolite windows. I've attached pictures of one that I have removed that still works. In photo #2 there is an 8 stamped on the coil. Can you help identify the appropriate replacement parts that I would need to repair the window? Also, the coi ... (cont.)