Viewing all customer Discussions for:

Door & Window

Hi, The roller pictured is one of two rollers supporting a wooden framed sliding patio glass door. I believe the rollers are at least 10-15 years old and have worn down to the point where the door will no longer slide. Upon inspection, one of the rollers has worn down off its track of the ball ... (cont.)

I'm trying to identify the snap-in glazing from some older storm windows without any apparent markings. It somewhat resembles 55-076 in profile, but the dimensions are smaller. An identification or suggestions for a compatible replacement would be appreciated.

Hi There, The metal portion of the balance is 27" long and 1/2" wide. The top is 15/16" wide and 3/4" deep and the bottom shoe is 15/16" wide and 15/16" deep. The sash weighs 23 lb. It looks like I should order a series 380 but I am not sure. The window is really hard to close and I think it is be ... (cont.)

awning window was installed 1998.its a andeson the part that goes on the window no. is C9400-1...........the arm no. is1521101

Hi, Could you look at the images I uploaded and tell me if you make a keyed lock I could install on exterior of door that either works with existing interior latch, or I could replace both? The door closes to the left when looking at it from the outside. Thanks Jared

I need a harvey 1658 L&R pivot set(your # 26-164), the one that shows in your catalog is not round on the bottom (like the one I have)but shows it open on the bottom, it looks like the correct set, but I wonder did the picture not show the entire product(the bottom) or has it been re-enginered. Tha ... (cont.)

Can you please advise whether the 81-018 is a suitable replacement for the Marvin part #10820000 or Marvin part #05550411, stainless steel version. I have not taken the doors down to inspect/measure the existing rollers. I would prefer to have the correct parts in hand at the time I remove the ... (cont.)

There are two of these that are in the window frame. The flat part attaches to the windows frame and the sprial is attached to the glass sliding window. Looking to find out what they are.

Hi, I hope you can help. This is an opening mechanism (or whatever you call it) :) for an older anderson window. Can you please let me know what would be the best solution.

Hello, I hope you can help. I have fixed drawer rollers (two on the cabinet and two on the rear of the drawer). I need to replace some of them. They appear to be nylon. The OD is 7/8" and the thickness is 1/4". They are riveted in place so I can probably make any ID you have available work. ... (cont.)

Good afternoon, I was unable to determine which of your items would best suit this window (NuPrime by Season-ALL). I have attached photos with dimensions. Looking for a pair of tilt window latches and a sash lock. Thank you kindly, ..Bill..

I need to replace a few shoes in our windows and hope my photos give you enough information to identify the part. My husband and I recently ordered pivot bars from you but now see that we need to replace some of the pivot shoes, also. We will also be ordering the jamb spreader once I know what sho ... (cont.)

this is a bottom track for a mirror sliding closet door.measures 48 inches long

Window is a discontinued MI Window, 1994/1995, series 150/250/350 (I think). No part numbers remain. Metal parts needed, eight (8), to replace bendable/breakable plastic parts. This 1" size part screws into top side of sash. It holds the spring-ballast in place. The picture showing ruler has ... (cont.)

The arm that extends the window out when turning the arm crank has become disconnected from the bottom of the window so I am guessing we need to buy a replacement kit. Also, one of the window latches is missing on one of the windows, preventing us from securing it closed so we need that replacement ... (cont.)

These are sash locks from an unknown manufacturer

My channel balance that needs replacing only has 2840 J stamped on it. Which stamp option should I select or does this even apply? The window itself weighs around 25lb's. It also has simple hook on the end of the balance that holds it under the shoe. Would you recommdend replace the shoe and ... (cont.)

Hello, We are looking for replacement window rollers for Masterview windows. I've attached a picture. Here are the dimensions: 1-1/8Lx1/2"Wx9/16"H. The wheel diameter is 1/2". The part that is inserted into the window is 1" long. I did not see anything on your site the looks exactly the same. Th ... (cont.)

Six windows all the same size. All my windows have red tip Balances. My bottom windows are 40"W x 22 1/2"H They weigh 30#. I need 5/8" x 22" Balances. Would the black tip be better for these windows. My top windows are 40"W x 43 1/4"H They weigh about 58#. Can I use 5/8" x 40" black tip bala ... (cont.)

There are four of these on the bottom half of the window. Two on the left side and two on the right side, one towards the top and one towards the bottom. I think they sort of resemble a screw on face guide, but not quite, this one has a different shape and little projections on it. I really need to ... (cont.)