Viewing all customer Discussions for:

Door & Window

I need to replace this wheel that came out of a Jeld Wen screen door. I bought the door in 2006. I believe that the part number for the door is JERL01790 Do you guys sell this?

We have 2 windows made in 1970 and also have windows made by Pella with crankhandle after 1990.The difference is the inside—hole size of 7/16 inch—slightly bigger than 3/8 inch hole in models after 1990. 1009 and 1011 are photos of 1970 crank handles and 1012/1013 are from 1993 windows with crank ... (cont.)

First off... I think this service is fantastic! I read all the posts and didn't find my sash balance. These are my numbers, what is the replacement? 11600-17 02 L9 1327 7-87 I'm curious by nature and was wondering what the numbers mean? Thank you, Tim

I need to replace the non-tilt window channel balances in my 1990 Viking windows as most are a huge struggle to close. The channel balance shoes, tops and caps are all the same. The only one I can figure out to match your parts is the cap which is number 18-009. The stamps on the 1/2" channel ... (cont.)

It's on the top of the window Prevent from opening to the inside of the room It's plastic

I am trying to locate a replacement roller for a 36 1/2" patio glass door. I have attached a picture of the roller assembly and of course I need 2 of them. I went through what you have lited on the web site and do not see anything compatable. I took measurments and included them on the picture. I ... (cont.)

Can you help identify the appropriate replacement part for my circa 1968 Andersen sash balance in the photo? EE 527 568 are the numbers etched on the old sashes. The visible glass on the bottom sash is 32" wide and 23.5 in length. No other information is visible on the sash other than the ... (cont.)

I have a marvin ultra window, the screen has two pins that you pull to remove the screen. how can I figure out what number these pins are in order to order more ? The pins are plastic, clear.

Hi, the lock no longer works on my sliding glass door. Can you tell me which handle to purchase. Does the new handle include a latch that attaches to the inside door frame? The door measures 59-11/16 X 80-6/16. I have attached pictures. Thanks, Cindy

I had Superseal windows installed 13 yrs. ago. The screen latches look exactly like your part #70-174 but they are smaller. They measure 15/16ths from the base of the lever to the notch and 1 inch from the top notch down to the base of the semi-circle. Do you know how I can get replacements ... (cont.)

I need to replace my channel balances for my Viking windows. The balances I have are 29 inches in length and 1/2 inch width. They have a stamp on them that says 2830n (or upside down u). I have sent pictures of the hardware on both ends.

Bottom of Operator 7702. On the arm is 07900. Handel is on the right-side of the operator. Split arm is on the left.

Hello: Do you have any of the attached window lock parts in stock? Thanks! Greg

Hello, Can you tell me which part I need to order. The teeth are all worn out and the window does not shut.

I have an OX sliding glass door handle with a plastic handle. the metal part has OX stamped on it with a patent number of 2,789,852. The little tear-drop level that move the catch to lock or unlock is broken. Does such a replacement part still available or can I buy a whole new handle. There is no l ... (cont.)

Dimensions of large rectangle are 38mm x 27mm. Tab with holes is 19mm x 12mm. Stamp looks like A*S. My window is warped on the bottom sill so I really would like to know if they make these with a tab that has slotted holes so I can adjust the height relative to the cam claw. If not I will probably t ... (cont.)

I need to replace Sash Balancers on my Anderson windows. The numbers on the balancer are as followers; D39 7P27 676 The windows were installed new in 1977. The visable glass is 32 1/2" x 19 7/8" Which balancer would I order? John

The38-036 casement window lock looks very close to the locks that i currently have. I too have the same Pat# 4,674,777 on the body of the lock. I would like to the distance from the locking arm to the point where the screw hole is. On my part the distance is 3/4 inch This measurement is taken with t ... (cont.)

Hi How high is the actual piece of weatherstrip from the faceplate. For example, how big of a gap will this piece fill. Also, do you have wool pile that will fit into the faceplate instead of buying the entire faceplate. Thx

I am looking for this type of sash balance for a customer. They are Traco Windows. They are spring loaded plastic