Viewing all customer Discussions for:

Closet

Hi, You label the hinge 23-401 as brasstone. We are looking for non-shiny brass hinges, something more like an antique brass. The photo looks like what we want, just wanted to make sure. Thanks, Sue

I found the 1/4" and 1/2" offset. Do you have a 1" offset??

I have a two 20 plus yr old 29 1/2 X 78" (actual), 1-1/8 wide steel frame bi-fold mirror door made by Monarch. I'm looking for the top and bottom post that were 1/4-20 x 1-1/4 long that went into a 3/4" wide track. The door frame has press fitted 1/2-20 nuts for the posts to screw into which can be ... (cont.)

I have 2 sets of Stanley / Home Decor Innovations mirrored bifold doors. The model number is 24-8282. I am trying to find parts for these doors to install them. I need the tracks (upper and lower) and maybe a few other parts. If you can help if would make my wife a happy lady. Thanks ... (cont.)

I have a back mounted 3/4 inch wheel with a 1/16 offset bipass closet door hanger that is at least 45 years old. I found a similar style hanger made by Kennatrack scottie but the wheel is 1 inch. Can someone help me locate where I can buy 12 sets of the 3/4 inch wheels. Thanks.

Hello! I am looking at your pivot hinges for closet doors. I am replacing a house full of old ugly louvered bifold closet doors. I would ideally like to replace them with flush hollow core doors on pivot hinges to achieve a more modern look. The hinges I see are labeled for bi-fold doors, but as ... (cont.)

Does Product code # 23-041 require 'specific' screws,bolts or nuts in order to mount correctly? Thank you. Shirley

I have a set of doors in my kitchen that are in front of a food pantry. I am not being successful in putting the doors back up. For For some reason the doors seem to be dragging on the bottom when being opened or closed. I have purchased pivot pins in the past but nothing seems to work. Springs ... (cont.)

I am looking for gravity pivot hinges to use with full size 80" doors that are 15" wide and 1 3/8" thick. I don't have a ton of wiggle room under the door or above it if I add it all together. How much space would be needed floor to door and top of jamb to door for the 32-064 hinges to fit and fun ... (cont.)

Hello, I have a set of Leigh Full=Vu metal bi-fold doors at my furnace closet. The opening width is 42 3/8 inches. each panel of the door is 10 1/8 wide and each door total is 20 3/8 inches by 78 1/2 inches tall. The doors appear to be in good condition but most of the hardware is either missi ... (cont.)

I am hoping you can help me ID a part that would connect our wood bifold closet doors with the track above them. I don't see any company markings identifying the brand. Attached are photos of the hole in the door from where the relevant part appears to be missing (approximately 1/2" diameter), t ... (cont.)

I have a non-operative Benchmark door and looking at your website, it appears I need to replace both my 21-044 guide pins. However, how do I install and adjust them? A drawing or parts diagram would be helpful. Do the plastic tips on the 21-044 ride inside the track or on the surface of the track ... (cont.)

How do you put a new top pivot bracket (like the 23-302) onto an existing track of a bifold closet door. The old top pivot bracket was partly plastic and broke. I cannot figure out how to install the new one without taking the track down, which I would prefer not to do. Is there any other way? ... (cont.)

Are the plastic inserts (wheel and screw) inside the metal brackets in 23-225 and 23-199 the same size and interchangeable?

I have Stanley mirrored glass bypass sliding closet doors. I have attached a photo of a part that snaps over the wheel assembly and acts as a guide in the bottom track. I need to replace a few of these parts. Can you help? Thanks. Rance

I need to puechase several of the brackets that are hopefully pictured

I have Benchmark steel bifold doors on all my closets and they are hard to open and close. Do i need to replace the whole pivot pins or could I get away with just replacing the caps that look like they are worn out?

Hi- I have original 25-year-old bifold closet doors in our Foremost modular home and need the following parts (see image below). Do you carry these? If not, can you recommend someone who might? If so, I specifically need two of the pivot guides (the metal/brown plastic parts shown below). These s ... (cont.)

My closet doors I`m working on are metal bi folding L series by US Plywood - A division of US Plywood Champion Papers Inc.A really old closet door.I need to replace 4 pins on these doors because they won`t tighten anymore.The pin is 5.5 in. long x .25 in. thick.They have a mechanism that fits throug ... (cont.)