Viewing all customer Discussions for:

Other

says it is an imperial USA door handle and it keeps bringing me to your site. The locking mechanism is fine just need the handle assembly. Thank you

Stamped 25 4. Length 25". Milgard windows. Need 4.

We need to replace the top and bottom door seal.

I need the black part that slides with the window

The window is 23" wide by 34-3/4" high, right-hand swing. Need the top and bottom hinges and the "keepers." Photos attached. The fixed arm is about 5.5" long. The pivot arms are about 5" and 3.5" long, attached to a 5" long sliding plate on the 10" long plate mounted to the window frame. Note: T ... (cont.)

Hello. I am a returning customer. I have to order a few 29" balancers with orange tips (I guess that is "red" in your description). The diameter of the metal part is 7/16 and the screw hole diameter is 3/16.I can seem to find the parts for that balancer. Also can you help me with the other two p ... (cont.)

Can you tell me if you are a part 32?341 would be the replacement for these two pieces? Thank you!

I am looking for a storm door handle from and old Cole Sewell door. It is a Wright handle and I am sure quite old. I have attached photos.

right and left side spring loaded metal latches that slide in to the window. I wish I could tell you the brand of the window but all remaining labels are too faded. There aren't any numbers or markings on the hardware.The external finger that protrudes and holds the window up often breaks, so many o ... (cont.)

Hi this is Larry with Ancilla Domini Sisters/The Center at Donaldson. These are the photos you requested to help identify the window parts we are looking for. Let us know if you need any more information.

This is Muglang brand. I need the lock only (not the door knob, as the components are separate on this door). What we currently have (on an exterior door) requires a key to lock it from the inside. I would like to switch to one that can be locked by hand from inside without a key present. Thank yo ... (cont.)

Checking to see if you have any of these spacers. There are 4 on each corner that keep the metal sash from rubbing the metal frame as you raise and lower the sash. Measures 5\16 x 3/16

can you send me guide to the job one side is stationary,

The pulls are a total length of 4 3/4" in length. It is 4 1/2" in length from center to center of the mounting hardware shown in photo 2. I will need 2 of these pulls and they do not need to match perfectly but would like them close. Thank you for any assistance you can give me! Debbie ... (cont.)

I am sending this email regarding this part for my Pella Windows. At the bottom of this email are pictures of the Window and where this part is in the windows. Kindly contact me and let me know if you happen to have these parts in stock. Greatly appreciated.

We would like to buy a new latch, to replace the broken one. We are able to replace it ourselves but are having difficulty finding it.

Overall dimension 38 1/8 X 24 1/2 inches Width X Height Screen frame is 1/2 inch thick in depth Frame is 3/4 inch all the way around on top and bottom and left and right side. Locking pin overall length 1 1/2 inch Extruding about 1/4 inch Spring travel about 1/4 inch Pin locking diameter 1/8 inch ... (cont.)

I am looking2 sash latches left right who go flat at top of sash with 2 screws.2 sash spring left right2 plastic stopper who goes bottom window.The sash is 19" x 21 1/2"There is no brand name or part number anywhere.

I bought American Craftsman windows series 8500 from Home Depot in 2006. The spring broke, I was able to remove the remainder of the spring from the case. The case has a 6 stamped on the side. The spring has 6DB stamped near the end. The case is 2 and 7/16 inches long, 1 and 1/4 inches wide and 9/ ... (cont.)

Hello, I accidently ordered part # 15-192 Shoes to replace the shoe in a simonton window' The size of the shoe is almost identical if that helps. After vwatching your video it looks like i need to order a different shoe pivot bar and possibly a new coil balance and coil supports as well? Let me kn ... (cont.)