Viewing all customer Discussions for:

Other

Looking for replacement mortice lock for Pella storm door mfg #06280290675 2046 found on door jamb. The plastic/nylon 'cap' on the catch is missing and won't retract to catch the strike plate to hold door closed. Thank you for your assistance. Fred.

Label from window and part pictured. Please send replacement partEd

Hi, looking for replacement latch for metal outer door.1" wide door3.5" mounting holes, with center spindle hole about 3/4" above lower mount.Don't need the bolt, just looking for something to latch as it shuts. Already have a deadbolt with key installed above this latch.Style not a big issue, but ... (cont.)

Pella sliding door exterior handle has a broken "screw post".

Looking for two of these.They are 30 inches long (metal part) and 1/2 inch wide (trade) widthStamped 29 6 HS CaldwellThanks!!Luis

This is a left hand sliding glass door for a client. I didn't take pics of the wheels in the frame. Each bracket has a metal two wheel system which straddles a metal center guide. Client states the metal guide got damaged and removed. Causing the sliding door to drag inside the bottom channel. We ne ... (cont.)

I placed a previous order and was successful with four of the screw mechanisms I purchased, but to were the wrong size (my fault). I need one left and one right of this size. Thank you,Kelly

Looking for replacement balancers for the product code on my Anderson double hung windows circa 1975. Code on my original is. C3 6 23 773. Any help would be appreciated. Thank you.Greg

Non tilt window, number indicated on balance: 23 3 GV CMC 7

I need to replace left side pivot pin (foot) that goes into shoe on Pella Vynal window sash. In attached picture pin appears as slightly L-shaped pointing up ward. Do carry his product? If yes, what is total cost including shipping and handling. Do you have instructions to remove and install new pin ... (cont.)

Hi, I am in need to replace the spiral balance for my windows. Please advise which spiral balance I need to order from you with the following information: Tilt window double hung Length - 35 inches Diameter- 5/8 inches Tip - it is very greasy but looks like white See attached photos. Thanks ... (cont.)

Looking for a lock set (interior latch) for this door. Has a keyed deadbolt. Registration # is 092704.90579.5581. None of the ones I've seen on your site look identical Thank you

Looking for a sasche balance for and aderson window.the house was built in 1985. Single hung window. I can see a number 11600.

The spring is 1/2" wide

Hi . My name is Tom and I'm a contractor. My client asked me to get new black hardware for his existing double sliding door (Weather shield ) brand.Style doesn't matter. Color is important.Looking at the pictures, look like striker is # 82-249Please find a rest of if plus handless. I have measuremen ... (cont.)

Hi, Could you all please help id this part. Thanks,Amy

I'm looking for vent arms for all of my awning windows. I don't see any names or numbers on the arms or windows. The plastic parts are broken on most of the ends. My arms measure about 8 inches from rivet to rivet. Any help will be greatly appreciated. Thank you.Rick

Cord inside channel broke.pulleys are worn so a new complete channel is required. A # on the channel is 2630 if that is of value.I think I would order two new channel to replace at the same time.Please help.

Hello,I cannot find a model number on my windows but these to me look like 150 series correct? I found the number #6 and #7 posted on the coil themselves. I just wanted to see if I am order the right parts below.#7 (S150-7) coilpivot shoe (15-140)cap (15-144)support barrel (15-145)#6 (S150-6)ThanksT ... (cont.)

Hello, I need to buy the locking mechanism along with the black-ish handle. I'm trying to call you but the phone call doesn't go through. I found the part number for the lock (82-227) but I'm unable to find the handle part number. Can you please give me another phone number of yours so I can call a ... (cont.)