Viewing all customer Discussions for:

Other

Looking for the correct bracket for the locking mechanism to latch into WHILE making contact with and depressing a pin that must be depressed for locking mechanism to operate. Picture shows track with 4 holes where bracket should be installed opposite locking mechanism that is also pictured. ... (cont.)

Eagle casement windows. Looking for the locking arm. The pictures show the window without the arm ( missing) and the other picture shows the window with the locking latch or arm. Also they come in left and right rocking arm from up to down position. Please advise Thanks

Hi, I have attached a photo of my window seal. please let me know if you can provide this or ant othe gustation can be used Thanks Lalba

I cannot find any markings on my window but the tilt lever on the left side is broken. The photos are the lever on the right.

Looking to match new outside and broken inside.

Please let know what replacement part number I should use.

Good afternoon, My house was built in 2008 with atrium windows. I have attached a picture of the lock that I have broken. The bare metal part should fit into the plastic one. The screw spacing for the smaller part is 1" and 2" for the larger part.

I am looking to replace the piling on the door at my store. the base of the removable piling in 1/8", the gap between the doors is 1/2". I didn't see anything that matched and looked similar to the old piling.

Please help identify if the a series 500 may work for my current project. Or if this is a custom balance. Thank you.

Trying to find the window operator for this style of window latch. Seems the little rubber part is damaged and window will not completely close.

Hi. I need to replace a Truth 45251 casement window operator with 9.5" arm (40049 stamped on arm). The distance between the outer screw holes is 3". The crank assembly (without arm) is 4" wide, 2.75" deep and 11/16" high. It looks like you have two possible parts that will work: 39-365/366 and 39-02 ... (cont.)

I ordered 26" series 350, 2510 and it fits great, but doesn't hold the weight of the window (replaced both sides - non-tilt) The only marking on my original is "25 4 FP CALDWELL" With out weighing the window, is there a better option for me?

I need to find an additional top swivel bracket for a ~ 1980 vintage Stanley bifold door kit. Looks like the pictures. Bracket is 1.125" wide, about 2.25" long and inserts into the track shown in pic 6539 that has a profile 1-3/16" wide and ½" tall. I also need a lower pivot bracket but haven't take ... (cont.)

I made a new screen door that's 35" wide by 96" tall. I don't know how much it weighs but it's too heavy for your 84-001. Do you have a roller with a stronger tension?

Good evening. I purchased a set of Pella 350 sliding glass doors. The keeper on the frame is missing. This is a picture of the lock on the door. It has 2 latches which are close to each other. The screw holes on the lock are 9 inches (center to center). The total length of the lock is 9 and a half ... (cont.)

I am looking to replace a shower door jamb which broke. It seems that this is very difficult to find. I have attached a photo of it You can see that the flat end (top of photo of the jamb) is 1 5/16 inches. That is the space that the metal frame allows for it to fit in. Do you have any idea where I ... (cont.)

Hey hope you have one of these - need a couple thanks for the help cheers chuck

Hi, My closet door has the left side missing the hanging part as well as the bottom part to keep the door on the track. I need to purchase one each. The two pictures shows the exact parts that I need to purchase. Can you tell me if you carry these two pieces.ThanksWinson C

I like to order two window channel balance: 32 4 IP Caldwell Thank you. Juergen P.

Only different between these 2 parts is the bottom and it's a 3/32 different. I think my part is the 385 series. If I'm not sure, should I error on the smaller size and choose the 380 or error on the larger size and choose 385 ? Lastly, the 16 inch balance, what is the normal weight support ? I ... (cont.)