Viewing all customer Discussions for:

Other

To remove sash you pulll the two latch on top(in picture)one on left and right side of sash

I need the inside handle plate only for a sliding door handle. The plate has the following names and numbers: SASH CONTROLS IND DETROIT 20, MICH 060-12555 The handle is probably from the mid 70's Door attachment screw holes are 3 15/16" apart Handle attachment screw holes are 4 15/16" apart I need o ... (cont.)

Looking got keyed lock for sun wood sliding door

The rail says Unigrass 6600. It?s the right side. I?d like to get a couple left and right sets in case it happens again.

Don't know why I am having a hard time finding this!Can you help me out -48" x 1 channels.

Pivot bar is for a Superseal window.The sash is mechanical. Remove the 4 corner screws and you have access to the tilt latches, pivot bars and the glass.

According to the people at Marvin Windows I need Dual Arm Roto Gear Operators with the following parts numbers LH 10815500 and RH 10815501.The Daylight opening width is 14 and 1/2 inches. Is that model you have in your catalog? Thank you, John

some of the plastic is broken. The numbers, if hard to read are 2220. I hope you can help me. Does the item come with the top and bottom plastic pieces included?

some of the plastic is broken. The numbers, if hard to read are 2220. I hope you can help me. Does the item come with the top and bottom plastic pieces included?

I am attaching a pic of what we need. It seems to be the S150 series spiral balance the tips appear yellow and we have 1 that is white.

Caldwell 25 5 KQ

I need a new slide bolt as the right one cracked and I cannot pull it in to move my storm door window up and down. Do you sell them and mail to Canada?

the numbers on the part that i have are NW1720-1, NW1720-2 and NW1720-3. the part has to fit into a 1-5/8" thick door

I was able to buy exact replacements in 2003, but can't find them now. The channel is 19-1/16 inches long. The photos show the relevant parts and markings. Window Master was purchased by Jeld-Wen sometime prior to 2003. They say these are Caldwell balances and the replacement is the Jeld-Wen 18-4. ... (cont.)

I need 10 channel balancers with the 2 ends in the picture stamped DB L02 2730. Another post said they had to be custom made. What is the cost? Thanks you!

Hello,I need to replace this channel balance. It measures 28" and is 1/2" wide. The numbers on it are 27 4 AW CMC 7. There is no stamp. The numbers are printed on. Thank you!!Eva

I am in great need of a couple window parts, and I am aware that ACAN is no longer in the USA. I have reached out to them, but have not heard back. I have the specific model for these windows if that would be helpful. It's that bar that houses the locking mechanism that I need to have replaced. ... (cont.)

The measurements are: 6 5/8 inch spread Lock hole is not centered. It is 2 1/2 inches from the top screw hole. I do not have the old set. Please let me know if you have a replacement. Thank you.

The windows are still good but the handle has stripped. I have a smaller casement by the same company that I might also want replaced. The part number is the same on the handle The second window is narrower and shorter but also a casement; I can send you pictures of that also if you have the par ... (cont.)

Trying to restore casement windows in a 1950?s duplex. Cranks could have been replaced at some point. Crank says Taiwan on underside. I am just looking for something to replace and make the window function so I can keep windows. It doesn?t have to be an exact match.