Viewing all customer Discussions for:

Other

Hi, I need two balances. The markings on them are: 28D USB. I've included photos of the original for the type of top and bottom clips. The bottom clip is 7/8". Both top and bottom have wings. Thank you, Kelly

Need to replace mortise lock. Thought your part 82-226 would be suitable equivalent. I

New discussion, hello, are these fasteners replaceable? Thanks

I have a sliding mirrored closet door guide that has fallen off the mirrored door. Do you by any chance have instructions on how the guide can be reinstalled on the door? The part # is the "Stanley 00-5024" Thanks for your help. Patti

I need sockets that have an opening height of 1" and a width of 5/16", and approximately 4" long. Which one do you recommend?

Looking to replace tracks for sliding closet doors made by Stanley/Monarch marked. 11117942

I want to replace all the snap in glazing on all windows for two homes. i have provide images of both. 1st house is a mobile home. Built in 1983. I attached the certification document detailing the manufacturer. Hopefully the images are sufficient to identify. So brittle from the sun that they di ... (cont.)

Hello, I need to replace the channel balance on one of my windows. I believe from looking around on the site, i have identified the correct part as the S380-33 (3250). The metal piece has a 3250 engraved on it. The metal piece is 33" long and about a .5" wide. Please let me know if this is the co ... (cont.)

Bottom sash latch for hurd wooden window

What will work for a replacement for this window. Plastic block is 1 1/4 x 2 1/16 x 17/32. It has a brake system.

I need a couple of drawer guides to replace some that have broken. Do you have one that will work?

Recently bought a mobile home and need to replace some missing and dry rotted snap in glazing. The ones I have are identical in measurements to 55-172 you offer but as you see in the photo and diagram I drew the front lip has a 90 degree bend that slides into a lip instead of the curve of the 55-172 ... (cont.)

See the image, could not remove the molding in one piece due to it's age. Measures 1/4" tall and 1/2" from left end of molding to vertical support. Lower right tab is approximately 3/32"and upper right tab is approximately 1/32". Small lip on the left side of the molding after radius. Installed ... (cont.)

We have the L-LC45 window that has latches that are screwed on the top of the window that the plastic has broken, from sun, I am sure. Where can I find replacements?

Hi, I have a Bi-Fold Closet door which is 6 feet wide and the bottom pivot (23-119) keeps on coming off from the door. A replacement does not stay for long. Does it come longer/bigger width, than the size of 23-119 so the door's weight does not give too much pressure on it ? Thanks ... (cont.)

Hello Swisco, I have Earthwise Double Hung Windows that we

Am in a small town in south central Florida ... no one seems to be able to help me with this weatherstripping I struggled to get out of two windows that were corroding and leaking water inside. There is a small channel that the weatherstripping goes into shown in first photo - It looks to be about ... (cont.)

Hello, hoping you can tell me whether you carry this part for a tilt out window. I don't have any other identifying information. Thanks so much.

Hi, I need 2 window balancers replaced. The window is a PGT single hung window SH - 4000. Model number is 6SHSTKR. The balance is stamped 29-4 LX CMC 7. The window size is 80 by 87 cm. I attached the pictures of the balancers. The length of the metal part of the balance is 76 cm (depth and width 1.5 ... (cont.)

The balance is of length 26'' but there are numbers marked as 25-5 at the back (as shown in one of the pictures). Would you please help to identify the window balance? Thanks a lot.