Viewing all customer Discussions for:

15-047 Pivot Shoe, 5/8" Thick

pivot shoe is 2" high 1-1/4" inches wide and 5/8" thick and it works with pivot bar 26-040.

Can you please tell me which pivot shoe fits an Owens Corning window. The model on the window is: FDH. It measures: 2 1/8" long, 1/2" wide and I cannot get an accurate measurement accross the shoe while it is in the track. Sorry... Thanks

Dear Sir. I had Wintech Industries double hung tilt-in vinyl windows installed in 1997. I need to remove pivot shoes. The side jambs/rails have no cut outs. I tried your 75-069 jamb spreaders with no luck. Vinyl jambs are too ridge. Do you recommend I cut out a portion of the jamb to remove th ... (cont.)

Hi! So glad to have found this site. I ordered a spiral balance charging tool from you, but after it arrived I discovered that the shoe at the bottom of the balance was completely destroyed. I managed to pull it out of its slot at the bottom of the jamb so I could take a picture of it. It measur ... (cont.)

Attached pictures of pivot Shoe? Approx size 2 in high 1.25 wide and 1/2 deep. As close as I can measure Help identify. Is there an up grade? PS Also sent you sample of weather stripping in previous request.

Hello, My townhouse has Patriot windows. Most of these windows have developed an issue in the same place. The screw on the photo doesn't hold and the rod (?name) doesn't stay in. I think they were probably over tightened when assembled. Also, the lubrication wasn't good enough and this contri ... (cont.)

I have a dilemma . I see the part number 15-046 that looks exactly like mine. But the measurement of the 15-046 is 1/2 inch thick. When I measure the shoe I have it neasures 17/32 which leads me to part number 15-015. The 15-015 does not look like the one I have . Which shoe do I order? Thanks. This ... (cont.)

I purchased the 15-047 pivot shoe worked on the bottom window but when you turn it around for the top window the little tab inside the black insert is on the wrong end.

I have a Pivot Lock Shoe that looks like 15-047, including the black cam, and matches all dimensions except for the thickness. I measure 9/16 inches with the cam fully recessed for raising and lowering the window. With the cam extended when tilting the window, I measure 5/8 inches. The channel ho ... (cont.)

No markings of any kind. No numbers or letters. Just looking for something that would work in place of. I'm in Toronto Ontario Canada and can't find anyone up here that sells parts.

Attached is a photo of the part that I'm looking for: Dimensions are 2" high, 1 1/4" wide, and 5/8" deep, though it might be a little taller as some of the top got crunched. I'm also wondering how I attach it to the little rope inside the metal spring bar housing. Basically, there's a sprin ... (cont.)

Would appreciate advice on availability of this part. Thanks Doug

I would need 12 and the tool to pull the spring down - let me know how to order - (the top metal insert broke so it's not in the picture - ) Thanks- Twad

I Have 20 15-047 terminal shoes ,they fit ok but the locking shoe cam are too short The cams are 1/2 inch and i need 3/4 inch.Thang You

Hello, I am looking for the part as shown in the attached images. It is 5/8" thick, 1.25" wide, and 2-3/16" long. I can't seem to find anything that looks close in your catalogue. I will be also be replacing the spiral balance with the 21" 600 series. Also, do you also have the plastic tri ... (cont.)

Hi, Please assist with which parts I need for tilt windows. The upper spiral balance is 26" (from metal tube edge to edge) and the lower sash is 29". I believe the width is a bit more than 1/2" wide with a red tip. That would be Series 600? The tubes and parts are fairly covered with grease ... (cont.)

Would like to see if this hardware is still available. If so would you contact. Would need a quote for the following: 108qty of 21" prod code S600-21 50 qty of the tilt latches "see picture" I couldn't find this on your website but the deminsions are 2 1/8 on center screw holes/ 54 qty o ... (cont.)

I am looking for the replacement pivot shoe for my windows. Can you identify which one I need from the pictures and the tool so I can order them?

Hi, I am Danny. I am working on rehabilitating 17 existing "Aluminum, Termo-break, Double Hang, Tilting Windows, and I need help identifying some of the parts I need. I am including a PDF of the existing Pivot Lock Shoe that I need to replace for the 17 Windows, totaling 68 "Pivot Lock Shoes". ... (cont.)

Our 10 yr old double hung windows made by PGT have several parts rotten. (See attached pivot shoe picture.) Our house is in Belize, Central America. It looks like Pivot Shoe #15-047 is the correct replacement. Just want to check that the 3" Pivot Bar will fit in it... I also believe that I will ... (cont.)