Viewing all customer Discussions for:

39-216 Single Arm Window Crank

Hi - I'm looking to replace this part on couple of windows. Please advise on a replacement part that will work. Thanks, Patrick.

Looking for a replacement operator for my casement window

I am looking for a replacement mechanism for this window. I found the oen for the other larger windows but can't find this one.

The spindle shaft of the crank mechanism of our Uniframe garden window has failed and will not re-engage. Company(Great Lakes Window) no longer carries the part. Recommended contacting Swisco for replacement. No parts stickers on window unit. Only part numbers located were Truth (hardware?) 40575 ... (cont.)

No part number

Hello, I wondered if two parts you offer will fit each other: Single arm window crank-part #39-216 Crank Hand Knob-11/32-part #39-115 Thanks,

Roller is worn and it always pops out of the track.

I need to replace some encasement window crank linkage that has rusted or broke. I also need some bottom seals. Hopefully the pictures will assist with finding the right replacement parts. Can you please advise? I have more photos available if needed.Thank you,Bill

I need one

Hello There,I would like to replace both ( Left & right ) of my CARADCO casement window operators 9-1/2" parts. The original parts have been working since 2000 with a single arm model as shown in the picture attached. Could you please advise me if is it possible to install the Caradco double ar ... (cont.)

I'm looking for what part this might be, for hte opposite window. We believe it' a casement window from crestine. We can see 4840074, but not sure what that is and also Truth. Any help would be great. Thank you!

Hello, I am in need of a few Crestline crank mechanisms. The windows open but will not close. The arm length is about 8-9 inches. Thank you Mark

Small kitchen window above sink - need both left & right casement operators. For my larger windows I ordered 39-031 - perfect fit. But kitchen needs something different & I can't seem to match it to your pictures. Any help - thanks. Julie

I need a replacement crank mechanism for a smaller Crestline window. The name listed on the crank mechanism is Truth. There is a patent number 4,840.075. On the backside of the long arm that connects to the window, there is a stamped number 40574. From the inside of the house, the mechanism cranks t ... (cont.)

Seeking direct (or equivalent) replacement for this window operator from 1993. (see photo)These are not broken, but the original design has always had excessive free play within the gear train, allowing the windows considerable movement. The end of the (~ten inch) arm can move by almost 2" just du ... (cont.)

The crank screw on my Pozzi window came out. I can open the window but when I close it, the screw comes out. Can I tighten it somehow, or do I need a new crank? The windows are 16 years old. Thank you Chris

Stamped on the assembly is "Truth" / Pat no. 4,840,075/ Made in USA. Also on one cogwheel is the number 3136 although I am not sure of the last digit. The house was built in 1996. Thank you for your help

I have Crestline Casement windows and need 2 right hand and 2 left hand operators. - They are all of the single arm variety. - The total single arm length is about 9 inches. - The body (where the gears are located) is about 5 inches long. - The operator looks identical to your 39-216 and 39-217. ... (cont.)

I have two kitchen casement window crank arm and operators I need to replace. One on the left and one on the right as I suspect that since the right is broken the left will be soon to follow. I believe this is truth hardware by the Windsor wood window brand.I'm very handy. I live in Bethesda, MD ... (cont.)

I am looking for a SEMCO casement window operator with the number 31538, it has a "Rivet to Rivet" length of 8 1/4" for a 17" wide window.