Viewing all customer Discussions for:

40-150 Inside Handle, 1-3/4"

My fiance and I ordered Part #40-150 inside handle on 7/22/12. It was delivered yesterday. However, we soon realized we also need the square rod hardware that goes through the middle, and the replacement handle hole is too small for the rod set up we have. Please tell me if we need to order the c ... (cont.)

What is the width of the base for the handle? Also will it work with a 5/16 spindle? thanks

I can't locate a name of manufacture for the door or any markings etc. I'm sending two photos which might be able to help. I was looking at your part number: 40-150

I just purchase this item from you and need to know how to remove the inside piece so that i can fit it to a larger size. How does that insert come out. Thanks, Mickey

I have ordered and received an inside door handle. it is item # 40-150. It appears to be the correct part, but the hole that goes over the center rod is too small. I'll bet it's adjustable, but I can't figure out how to do so. Can you help me?

I bought Swisco part number 40-150 to replace the door handle on my Forever Door. However, the inside doesn't match up with the current exterior handle. Can I purchase new outside handles that will match the 40-150?

Door handle has no spring. Do I need just an inner handle or both outer and inner? Which model looks like a match. Bought from home depot about 7 years ago.

my front and rear door handles are discolored my front door serial number is 3602452 and my rear door is 344507 could you tell me the part numbers so i can order them please !

I am able to get the spindle insert on the new latch out OK but cannot get the spindle itself out of old door latch inside handle assembly. Any trick to removing or is this another replaceable part?

Does the 40-50 come with the screws?

i need the inside handle replaCEMENT THE SPRING IS BROKEN AND WONT LATCH PROPERLY

The spring appears to have broken on the door lock set. I am enclosing 2 photos of the front and back of the set. I would like to replace the entire handle/lock set.

Does part #40-150 have an internal spring that rotates in both directions to return the outside lever to the neutral position. My lockset works fine except the internal latch spring broke. The hole spacing is 1-3/4" like the picture shows. I am a retired contractor, this is for my home. I have a ... (cont.)

The product description indicates that I can remove the insert to fit my spindle. I need to do this (otherwise, everything fits perfectly). But how do I remove it? There has to be a trick I haven't figured out! (I tried to pry it out with a screwdriver - that didn't work.) Thanks. Coll ... (cont.)

the door latch on my front storm door just spins around 360 degrees and I can't figure out how to fix it. I was wondering if I need to buy a new latch. It is a "The Forever View" door with a serial no. A-153395. I have added an image of the latch. the other side is a brass lever door handle. Thanks ... (cont.)

The spring in the door handled had broken and I have ordered and received the replacement top part of my storm door (40-150) from a photograph on your website that a customer had the same problem. I need assistance in helping to install this part. Can you assist me ASAP?

I have a Forever View Full Glass door. The serial number listed is A-824493. The glass size is 75" tall and 31" wide. The brass handle broke and I am looking to find and replace.

HI: I think teh 40-150 is what I need to order. However I would like someone there to review my pixs and confirm that it is. The Storm door has no ID on it. I checked the web and after reviewing 17 pages of handles. the 40-150 looks like the most similar and from the other comments I have read. C ... (cont.)

The spindle size on my Forever door measures .32" across. The description for the 40-150 indicates 1/8" or 3/8" spindle. Will this work for my application? Thanks!

I have Emco Forever Door Storm Door, Series L 647318. It is 1 " thick. The inside latch is broken. Do you have a replacement for that? Thank you