Viewing all customer Discussions for:

70-195 Window Screen Pin

Any suggestions or helpful info on sizing/making the receiving holes in the wooden door frame? The screen I'm making is for the top half of a split door that was not originally built to host a screen. I'm imagining using the spring loaded plunger pins on all sides of the aluminum screen frame to fi ... (cont.)

from vinyl, single-hung, new construction windows purchased at an 84 Lumber 10 years ago... One of the windows has a model 4201 white on an information tag. The pins are very similar to your 70-195, but do not have the shoulder, and are a little shorter. I'll try the 70-195s, but wanted to see i ... (cont.)

What is the metal of the plunger pins? Being located ~150ft in from the surf, all of the original aluminum pins of my MW Twinseal window screens, on the ocean side, had corroded and seized by the time I bought the place 5 years after being built.

My window screens are setup with the 4 plastic tabs that are always breaking. How can I retrofit this top tension and possibly a leaf spring into the frame of the screen ? I was thinking a drill and a rivet set might be easiest but was curious as to what you would recommend. Many thanks ! ... (cont.)

I need replace broken plastic window screen retaining pins. They are L shaped, the pin is approximately 1.25 - 1.5 inches long. The L makes a "lever" that helps to remove the pin when the screen needs to come out.

See picture - do you have this size?

The screen is held in place by 6 plastic nail like pieces that you push in when the screen is in the track. My windows are 10 years old and everytime I wash them more and more of these fasteners break off. Do you sell them? THANK YOU TONY

I purchased a fixer upper condo that was originally built in about 1972. The screens are original and the pins are so old they were dry rotten. They were completely plastic. I am trying to rescreen the screens as the frames are good but need to replace the pins as well. How can I properly identi ... (cont.)

Need to purchase screen plungers for Superseal Mfgr. vinyl windows 911 yr. old) The pin is plastic, little over an inch with a round head...Advise if have and the cost ?

I am looking for replacement screen pins for Weather Shield screens. This house is located three blocks from the ocean, so the metal pins that came with the screens corrode in one season and become inoperable. Is there a replacement pin that is less susceptible to corrosion?

this is on the top of a screen it only goes through the frame to the spline track not all the way through

White nylon pin used to hold screen in place.

Do you have a version of 70-195 that is a little longer? And a version of 70-009 with a white head?

We need some (maybe a dozen for spares) spring plunger bolts or screws for the Super Seal screens. They are small white, plastic screws with a round head (4 to a screen) that hold the screen in place. Can I easily insert them, or will I need a special tool?

Hello, The large rectangular screens (I do not know the manufacturer) in the house that we moved into are designed to have two plastic posts on top. The posts are about an inch or two high and have a threaded end and they fit into a channel to keep the top half of the screen stabilized. The low ... (cont.)

The pin fell out and I can,t find it.I need a few replacements and instructions on how to install.

My pin is from a sliding glass door frame. Circa 1968 They are white plastic with a small flat head. The post is about 1" long and 1/8 " in diameter. They are pull outs so I can remove the grid to wash the windows. Some have broken from use. Any ideas? Thanks, Pat

My house has about 16 casement windows and screens with really cheap plastic retainer pins that seem to break if you look at them wrong. Forget trying to remove them for cleaning. Can you help me identify what I need? I have no idea as to the original manufacturer of the windows or screens, as we ... (cont.)

I need to replace a few of the pins that hold my screens in place. The ones that came with the screens are plastic, but I don't require that the replacement ones be the same material. I don't want to have to drill a hole in my window frame, because there is already a piece of hardware installed in ... (cont.)

Why the dimple have way up the pin? Is there a version that is free of the dimple?