Viewing all customer Discussions for:

81-018 Sliding Patio Glass Door Tandem Roller

need replacement rollers. Access to adjustment screw is from in the house. Middle hole in the pictured part.

Sorry I believe the rollers are 1 1/2 and 5 3/4 hole to hole.

I have a customer who was installed years ago before our store opened and a different location had done the installation. The customer is requesting replacement rollers but due to lack of information provided when I received the file and no serial numbers on the products we are running into dead end ... (cont.)

Need rollers for a traco sliding door but unable to find the serial #

I'm looking for the roller assembly for a Doormaster sliding glass patio door. Dimensions are:Width: 5/8" at the widest point; 1/2" at the endsHeight: 1 1/4"Length: 6 1/2" overall; 5 3/4 from center of one screw to the center of the otherWheel diameter: 1 1/4"Wheel material: MetalThanks for your hel ... (cont.)

Looking to order replacement wheels for our sliding door.

The attached photos are for a sliding vinyl glass door. The rollers are 1.25 inches and the other measurements match those listed online. My question concerns the nylon spacer on top of the roller. Is it necessary and if so do you have a match. I don't know the manufacturer of the door. Thanks, ... (cont.)

I need to replace a roller on my sliding door. I think it is 81-018, but not sure. On Del-Mar website, F3731 seems to be the closest one. If you can kindly help me out, I would be appreciated, thanks.Yifan

This is a tandem roller on a Revere sliding patio door. Door is one of two sliders with 2 solid panels. Unit is 12 ft wide and 8 ft tall. Approximately 12-13 years old. Tandem wheel unit looks like your 81-156 model with end adjust. The 81-156 shows to be 1.5" width/tall on the carriage unit wher ... (cont.)

Hello, We are looking for these replacement rollers. The names them says delmar. Hialean . Thank you,

Wheels are 1 1/4". Appears to be 6 1/4" long. Says Del Mar ENGRG Co stamped on it. In need of two replacements. Thank you, Ryan

Hello, I do not know the manufacturer of the sliding glass door. The door has two holes in the front and no screws in the sides for adjustment. So, I think it uses one of the tandem roller designs that you have. I think it is one of the following: 81-018, 81-128, 81-141, 81-149, 81-182, 81-188. A ... (cont.)

I have a Gorell sliding door. Both sets of the wheel systems need to be replaced. They are about 4.75 inches long. The door is about 10-12 years old. Unfortunately, I do not have a model number Thank you, Bob

Theses are the numbers on my sider i need to replace the rollers. SGD-R30-144x82 series 910. Having trouble finding the correct roller set

I'm looking for rollers for Republic Sliding Door and also rollers for the Screen Door. Do you have either of these available. If so I would need to have them shipped overnight, I will pay for shipping. Thank you Mark

I believe I have Peachtree ariel double sliders going out to my deck. 4 pane, 2 sliders, approx 10' total width. They were installed in 1986. I want to replace the double roller wheels, 2 sets under each slider. I believe the parts are you number 81-018. I can't figure out how to get the doo ... (cont.)

We are a Glazier company in Sweden. We have supplied and fitted thousands of sliding doors in Stockholm, Sweden. In the next few years a lot of them will need wheel replacement. For many years we have bought TRUTH 31761A wheels for sliding door from a supplier in Sweden. They now have stopped sel ... (cont.)

You can zoom in on the part number. I'll need 2 sets

Looking for 2 Rollers

Looking to replace 4 of these roller mechanisms for an Anderson Sliding Door.