Viewing all customer Discussions for:

82-226 Mortise Lock, 4-5/8"

need to replace this handle. do i need the metal part in the wall that it latches into as well? can you tell which size based on my photos? the lock latch broke completely off

No ID on glass slider. Only etching on glass identifies PPG Herculite K glass. Door has been painted so ID may be covered. Looking for the keeper that goes with this reach out mechanism. Keeper measures 4 inches total height. Vertical screw holes measure 3 inches. Keeper width looks to be 3/4 ... (cont.)

Hello. I have 2 doors with these handles that don't latch properly and need to be replaced. Can you assist in finding a replacement? I don't care if it's exact, just close. Please see attached photos. Thank youPaul

The lock on the sliding glass door does not work any longer. I need the proper replacement part since the door manufacturer went out of business. Can you help me identify and purchase the proper lock?

I need the handles and the internal mechanism ThanksKen

I need to buy a new lock to replace my entire locking handle for my sliding door. There is currently no lock on the door. Every time I buy a kit, the screws are too short to fit the door. What kit do I need to buy from you that will fit? The manufacturer number for my door is NFRC 100 , code: Hll-28 ... (cont.)

I need to buy a new lock to replace my entire locking handle for my sliding door. There is currently no lock on the door. Every time I buy a kit, the screws are too short to fit the door. What kit do I need to buy from you that will fit? The manufacturer number for my door is NFRC 100 , code: Hll-28 ... (cont.)

Will this work for my 2000 Anderson patio slider.

Sliding door from M&W. 25 years old. Spring inside of latch has broken (again). I have repaired it twice over the years by repairing and re-using the original spring but it will be difficult this time. I am looking for a replacement spring or the whole latch if i must. Can you provide me with p ... (cont.)

Good evening- I have a sliding glass patio door and the handle broke. See picture with broken wood handle. I purchased the white handle but it does not sit flat against the door since the new handle has slight nipples. I was looking to see if you had a handle that would sit flat against the door. ... (cont.)

Need to replace the lock and handle

Hello my landlady wants me to replace the lock for this handle. Do I need a whole new unit? Should I call a locksmith?

My handles have broken off and I need a replacement set but I'm not sure which one I need.

Need this replaced!! Mechanism dosnt work right and lock tab is twisted. This is the only source I have found to ask questions. I just want to confirm exact part and find a fast deal for a good strong replacement.

I am trying to find a replacement locking handle for a WENCO patio door Holes are 3 15/16" Door is 1 5/8" thick

Hi we need a new door handle assy and hoped you could help us.Thanks - Ron

Hi, our lock is worn out on the patio, and I've identified part 82-226 (4 5/8" mortise lock) as the replacement. While we're at it, we'd like to replace the inside and outside handles. We'd like white, silver or brushed nickel finish. Do you have some choices that would fit?

The inside lock fell off the door. A piece inside of it broke off See pictures. Descrip.6068 72?x80? FCRO Wh VS/I/TAA/DS/H white right open dbl str. TmprA 9050-1000-00 106-0100-000 Thank you.

I bought the 82-226 4 5/8" mortise lock and the 82-106 turning lever. However, before installing them, I found the existing door handle base added extra thickness that might prevent the lever from reaching the turning slot on the lock. Also, the hole on the existing handle doesn?t seem to be able to ... (cont.)

the part is 6 inches long x 3/4 in wide. the distance between screw holes is 4 and 5/8 inches