Viewing all customer Discussions for:

S351-27 27" Series 351 Channel Balance

Hello, I'm looking for the original channel balance for my vertical lift bathroom window. The channel length is 27" Channel depth is 5/8" The part has an ID stamp that shows 2640 Thanks

8). #2620 channel balances. 26 3/8"10). #1820.channel balance. 19" 4). #2420 channel balances. 25". 4). 90-042 NuPrime Window Sweep 36) 18-110 NuPrime SeasonAllFour windows with #2620 channel balances have balances on left side only - two windows with #1820 stamped balances have one on ea ... (cont.)

27 inch with 2630 stamp

Please see photos attached. I need a number for Milgard window balance: 5/8" width, 27" long channel 2640 B.S.1. If part no longer available what is the best alternative. Thank you!

I'm looking for replacement parts for single hung Repco vinyl windows. I have attached several photos below. Please let me know if you have the appropriate channel balance. Thank you.

Need some help to identify the window balancer part. the lenth is 26. 7/8 for the metal part Please let me know if anything else is need

Hi Believe I have a BSI 2630 per pics. The metal bar is 27" long (not including plastic ends). Look correct? If you need more pics let me know! Thank you

Window #1 Hi - I am trying to figure out if I can fix some old windows on house we bought recently. For this window, Window #1 (center window of three window front window) the balances were popped out above the bottom window and flopped inwards. I was able to remove the balances following your vid ... (cont.)

I am trying to replace my window balance due to one side broke. I believe the series 390 27" is what I need, but I wanted to seek your help. Thank you!

Need channel balance for IWC non-tilt window. Metal channel is 1/2" wide and 27" long. Refer to 5 attached pictures for markings on channel and plastic pieces on each end. Please advise on ordering of replacement part. Thanks. Gary

Metal channel is 27" not including plastic ends.

This window balance if for a non-tilt out window. The markings on the side say 26 4 BQ CALDWELL. The length of the actual metal portion of the balance is 27" and it's 1/2" wide. From the ones available on your site it looks like it could be an S351 or S390 but I can't tell which one. Thanks for ... (cont.)

I need 2 new channel balances and can't quite figure out what part matches. The brand is IWC (Internatioal Window Co.) The length is 27 inches (just the metal). The markings on the side are 26 4 EU CMC 2. Can you please help by letting me know which of your parts is a match? Thank you! ... (cont.)

Length is 27 inches. Would you tell me which model I need to order? I like to order 12 pieces.

I am looking for the complete set of both sides (left) and (right)including clips and all necessary parts. if you have any question, please call me

I've included photos of my balance. The metal channel measures 27in. Attached are photos.

If you guys can help identify what I need. I'll be happy to purchase it from you. Thank you so much for the all the videos. They made it so easy The metal is 27" long

Good day, I have removed my old channel balances on my windows and these need replacing. Please let me know if there are any more pictures that are needed to identify the proper replacement balance

Hi ... I need to identify this 35 year old Milgard balancer. The sticker on the window frame says Series 1500 , DH-R20, MST: 4060The only numbers on the balancer are 2603Eonline I have seen 2630ec, 2630ep and 2630ex. Could you please help me identify the correct part ?Thank you,Ray ... (cont.)

Hello, I'm trying to figure out what part to order to replace my window channel balance. The string broke, so if I can just re-weave a new string into there, that would be good to know. The channel portion is 27" long (just the metal part, not including the plastic end). The stamp on the left side ... (cont.)