Viewing all customer Discussions for:

S380-29 29" Series 380 Channel Balance

Hi. I have an older window sash, from a house built in 2005, that I need to replace. It's marked as 28F USB. It's a one-half inch channel with a length of 29 inches. The photos I uploaded show the broken sash next to a new one - one of your models, 2820. The new one is on top. Note that the spring i ... (cont.)

Need 2

We are trying to replace these springs on our windows .When we removed Sash the springs fell out we need help locating correct springs.

I need window balance channle. the stamp says 28C and 28D. On your website can't find the same stamp. Could you please tell me which one is compatible with 28C and 28D.

I think I ordered wrong (2840) it seems.These are 29 inch long and 1/2 inch wide and has 28-C stamped on them.From above would you please identify what part do I need.Shoe is about 3/4Thanks,Bharat

Good day! I could use four balancer parts. I look forward to your reply. the metal part of this is 29 inches.Bob

I need some channel balances for this unit. The windows are from Florida Extruders International They are the Milestone Single Hung Series 1000. The channel is 29" long and 1/2" wide. The spring is 14". The only marking is 28B. It seems similar to your S380 other than it does not have a ramp ... (cont.)

Stamp 28C USB. CHANNEL is 29" long. I need 22 new channels. Replacing 11 window channels. From reading I need the plastic pieces on top and bottom. Looking for some guidance as to what series to order for the channel along with the plastic top and bottom pieces. Thank you

Hi, I need a block and tackle window balancer for a hurricane impact window sash. It says "Stamp F." If I understand correctly, that would be Stamp 2860. thank you, --Mike

I recently made a purchase for balancers, but unfortunately, I purchased the wrong ones. I have a total of 11 windows that require replacement balancers on both sides, meaning I will need a total of 22 balancers. I have attached pictures of the balancers I currently have. Could you please reach out ... (cont.)

Metal component is 29" long. Stamped identifier is 28F

Window channel balance for non tilt window. 29 inch metal marked with 28 6 PN BSI.

Hello, I just bought a house and ran in to an issue where the spring popped out of the window. After some Google/Youtube-ing, I'm learning that the issue lies with the window balances. Attached pictures, but also listed the "stamp" details below - looking to replace both sides with all pieces (which ... (cont.)

Hello, My bedroom windows all of sudden came off the rack/rail and I noticed it's broken. Could you please let me know what part should I purchase. Thank you for your help Fred

On one side there is the number 28C USB but the spring is connected to a pin hole shorter than on the other track that as no number in it ( see photo attached with side by side pics ) . The metal Channel is 29 ? long and it's for 51 inch windows , I have 7 windows that I need to fix . ... (cont.)

length 29" Width 1/2" Stamp UB 28C

I need 2 sash guides with 29" channel messing 9/16 x 5/8. I thought I Found it but smaller end looked wrong. It has a 28C stamped on it. No other markings

We have a house built in 2010 in Sarasota FL. One of the channel balances on a window is broken. The metal part of the channel balance is 29". Printed on the channel balance are the words 01/10 Unique 28-F-60. A sticker at the top of the inside of the window frame says: "Keystone Certification Pr ... (cont.)

The only markings that the old balances have is 28B

Hello,I am the owner of the town house and I want to repair my windows. I need your help for change the windows balance and the Top Sash Guides.The windows balance dimension is : - 29inch leng (without Balance top and balance shoes) or 30 inch for the full balance system.- 1/2" Width- I can see one ... (cont.)