Viewing all customer Discussions for:

21-106 Bifold Pin Cap, 3/16" ID

I believe that I need part # 21-100.... a nylon guide post cap. However I am not totally sure that this is the correct part. The pictures that are included shows the two posts, the pivot post has a smaller diameter cap, which I do not need. I do need the nylon cap that is on the larger diameter g ... (cont.)

Howdy. I'm looking for this by folding door guide. ID,1/4 OD. 3/8 Hight 1/2 flange OD 1/2. All guidance welcome.

I need to replace the plastic caps on the end of the metal rods. Rods are 5/16. Doors are about 50 yrs old.

this pin is a shade under 4.5 inches long the cap is about 5/8th

Hi, we have a mirrored bifold door that is about 6'6" high x 5' wide. I am guessing it weighs 50 lbs. In the midst of a remodel, it appears that I have lost the lower pivot pin bracket. I am attaching a picture of the pivot pin to give you an idea of the system I need. It has a 5/16" thread and a ny ... (cont.)

Hi, my name is Maddy. I have a few metal doors that need new hardware but I'm not sure which one are the right ones and local hardware store does not not carry. can you please advise me on what I will need to make this doors work like new? I will appreciate your help on me placing an order to find w ... (cont.)

I have ordered some nylon pivots,21-101 and 21-105, and a couple of our tracks (mainly the bottom ones) are wore out. Would you know where one could purchase this track. The pivots I ordered I hope the are right. I ordered them from you. On my track, the plastic pivots ride on the outside of the ... (cont.)

I have been looking for a replacement plastic knob that fits on the end of the metal pin into the floor track of these metal bifold doors. It is actually the white piece in the pictures. I need one of those for a different closet door that is of the same style and make. I could not find any markings ... (cont.)

I have a US Plywood metal bifold door and I need replacement pin caps. The pin is 5/16" in diameter and therefore requires a cap with a 5/16" inner diameter. Do you have any images of the pin without the cap, or the underside of the cap? Is this pin entirely 5/16", or is it a smaller diameter u ... (cont.)

Hello, I have Slimfold Bi-Fold Doors that came with the house when it was built in 1988. The metal pin that I have has what looks to be threads at the bottom of the pin. I need to replace the top cap that fits on the metal pin that broke yesterday and runs along the track when you open and clos ... (cont.)

Depicted in the photos below are 2 bifold metal doors to my laundry area; age probably 1974. One bottom pin cap is missing(broke off when man removed doors to repair washer). It appears to fit over a 1/4" threaded pin. The cap itself is about 1/2" tall, with about a 5/8" flange (is that the right wo ... (cont.)

Hello, Based on posting/pictures already on your site I have identified the bifold doors in my house as old style Slimfold. But I had some questions about the parts I need. Want to replace all the pins and brackets. Are the pins and brackets on the top same as bottom ? That is the pivot pins, guid ... (cont.)

Need just the nylon cap. Couldn't find it in the accessories.

Hello, I have a framed glass shower door with plastic/nylon pivot door hinges. The tope hinge snapped and I'm trying to find a replacement. I'm not sure if it is by SWISCO, but in searching online, pictures of your hinges came the closest. Unfortunately, there are no part names or numbers on t ... (cont.)

Attached are photos of the top of the metal bi-fold pivot. I also needs some of the threaded parts for the bottom pivot. At minimum, I need (4) springs, caps, and the best device to hold in the pin. The pin is 5/16 (.310) x 5 1/4" long. I was looking at parts 21-065, 21-001, 21-007, and 21-154? ... (cont.)

Hi - I have 2 metal bi-fold louvered doors; one of them is missing a couple of parts (I have pictures of the missing parts -- pictures + some comments added to them ... with the names of the parts maybe incorrect in the pics). 2 of the following (top of door): 6.5" pivot rod; 1/4" diameter; sp ... (cont.)

I have looked at pin cap 21-106 for my 5/16 pin. Can you tell me if the bottom inside dimension of the cap is 5/16? The specs on that show only the top. If there is a lip on top this could be the one for my door. It is shown as a related part when looking at the pin with spring+cap or pin and cap as ... (cont.)

I have three sets of doors by US plywood. The pins are 5/16 by 51/4 long. The top pivot pin looks like the Fenestra pin and spring. the bottom slide pin is threaded at the bottom of the pin with the nylon peice measureshole size is 3/16, the ring is 5/8, and the end is 3/8. I am not finding the repl ... (cont.)

Do you sell just the nylon pin caps to fit the pin 21-005? I nedd about 60 of them. Thanks, Matt