Viewing all customer Discussions for:

21-277 Bifold Track Bumper

We are trying to install a set of used doors that are 36 inches wide and we need to have the tracks that will fit the three eights inch pin on the doors

I would like to get all new tracks and hardware that sits inside the tracks for my 48" metal bifold closet doors. I have 5/16 inch pins and plan to reuse those. Can you take a look at the attached photos and let me know what you recommend? The bottom track is 1 1/8 inch wide measured from the out ... (cont.)

Hi. Bought the home . No clue of manufacturer or when they were put in. No one seems to know 1. How to replace or 2. Where to get the parts. Gosh, I hope you can help! There are a bunch of these in the house so I assume will happen again. (The top one had a plastic cap.) Pix below. Thank you for you ... (cont.)

Hi Frank. I recognize these parts from old Slimfold bi-fold doors. For a bottom threaded pivot pin, see the 21-001. For the guide pin, see our 21-007. The clamp can be replaced with our 21-154. If you need bumpers, see our 21-277. Look over all parts to confirm that they match your old components. W ... (cont.)

Fast learner, but still thawing from the long winter so maybe a little slow.................. Peachtree 8' tall bifold doors. These are in a 30 year old 8 plex apartment, and basically cover one wall in the kitchen. Half of it being a coat closet, and half being a pantry for the kitchen (or just g ... (cont.)

Hello: I need help identifying new hardware for my bifold doors. I need as well new tracks. The old tracks measure 30 inches per one bifold door (4 tracks top and bottom) and 2 feet per bifold doors (4 tracks top and bottom) Thank you for taking the time to help me.

Hello, I am looking for this piece for 1993 bi-doors. Can anyone help me? Thank you.

The product number on the label on the doors is BJJDFG. Attached pictures of the guide pin and clamp. All clamps have cracks in the plastic but I am not missing any parts otherwise. I am also interested in replacement track bumpers. I have 11 doors that require new pin clamps on 6 closets. 5 have do ... (cont.)

I have a Slimfold, 60 inch, 4 panel metal bi-fold door which needs a new lower track. The old track is 11/16" wide and 11/16" high.

Bottom connector to the guide in the floor. The top of the long rod has a slot to adjust the height of the door with a straight screw driver. No manufacturer's name o Rd number is available. The door is about 26 years old.

How can I hang this type of door without putting a track on my vinyl floors? What is the part number for the Pin with the spring at the top of the door?

I need the top tracks and pins for the bi-fold doors in the pictures below,are these available? This house was built in 1957 and these are the original floor to ceiling closet doors

Hi friends,We are facing difficult times with our metal doors in two of our buildings. We are a non profit housing organization called MTR - More Than a Roof Housing Society and we wanna replace our tracks and pins (not the metal doors) by new ones, probably different ones... Today we use parts like ... (cont.)

Need 8 feet bottom track for JFBAFG bi fold

I'm looking for a 96" bottom track

I'm looking for a 96" bottom track. Please contact me at Luongtienq@yahoo.com or phone number 4084161171 Thanks, Tim

Hi I have bi-fold metal doors, 3 feet (1 door), 5 feet (2 doors) and 30 inches (1 door). I am going to replace all the pins and tracks with your help (of-course). Can you tell me the parts needed. Thanks P.S. I researched on SWISCO.COM and I placed an order (1139482) based on what the parts for on ... (cont.)

I need the center bumper for my bifold doors and the bumper that keeps the door apart when closed (to keep from binding)

I have an old Leigh Metal Bifold door that needs a new bottom track, cap and bumper. Approximate measurements for the existing track are: Length 3' Width 1" Height 15/16". Would your Part 21-401 track be an acceptable replacement and what other parts would I need to finish the set up for the new tra ... (cont.)

I need two tracks 10 feet long for the ceiling and two tracks 10 feet long for the floor And 22 pivot lock One 3 feet ceiling track & One 3 feet floor track