Viewing all customer Discussions for:

81-098 Pella Patio Glass Door Roller Assembly

Have a Pella slidind door needs roler.Installed in the 80',Which Rollers do I need.

Hi, I have a Pella 72" x 80" sliding patio door that I bought from Home Depot Canada in 1996, I am looking for replacement rollers for the glass sliding door. Although I have the original receipt, it does not have a part number on it. Are you able to recommend rollers for this door? They are 1 1/2" ... (cont.)

Sent images 15,18, 21, 22 and PDF of dimensions No brand markings on door or mechanism. Vintage approx 1963 when house was built. Very heavy double glazed 7 foot tall by 39" wide all wood frame. Unless you have a perfect match to my dimensions,your 81-249 is as close as I could find. I p ... (cont.)

Need to replace roller assemblies for older Pella exterior sliding glass door. See attached photo. House was built late 70's early 80's and guessing this is original door. Can you tell me which part number I need to order?

Will the pella sliding patio door roller 81-098 fit a Mid 80s door

When my home was built in 1978 or 79 a Pella sliding glass door was installed leading to the deck. The door is wooden construction but has no metal cladding. After careful inspection I have been unable to find a model or serial number on the door. One of the roller assemblies has failed making the d ... (cont.)

I am replacing a roller for Pella slider OX-26CX installed 1984. Please confirm that this is the correct roller. I prefer no to remove the door just to see if there is a flange. Thanks!

Hello, I am looking for a Pella slider door handle -(we just used rollers we ordered from you- part # 81-098) the center mounting screw holes are 6" 5/8 to 6" 3/4. (our customer bored holes to make larger and am not sure of true measurement) What we need looks like your part # 82-218 but is too smal ... (cont.)

I need to replace the roller assembly pictured in attached photos. Unfortunately there are no identifiers on either the assembly or door itself. I can tell you I think the door is appx 1992 vintage. The measurements are 2.75" long, 1.75" wide, and .75" thick. Wheel is 1.5" diameter. Can you giv ... (cont.)

are the rollers adjustable?

Hi I need two of these for our older sliding door. I did not noitice any markings but I think the door might be a pella. I hope these pics. If you have them could you tell me how much they cost abd I will order. Thanks Ron

No markings on part.

I need to replace the rollers on my Pella 5

WHAT IS CORRECT ROLLER FOR PELLA 8FT SLIDING DOORS DATED 1985?

I believe my Pella sliding door's rollers have been slowly going over time. It's been getting more difficult to open each time I do. I also noticed that my rubber bumper stop is cracking. My Pella door is approximately 10 years old. I'm looking to replace the above mentioned parts. Thank you in ... (cont.)

Glass is etch marked 3421989 Also 16cfr1201 c11 Anson z97.1-1984 1/8"

I have a vinyl Pella sliding patio door. I need to replace the rollers. The product ID is difficult to read but looks like MO210047776-NFRC May 7 2003 94 Can you help with which are the appropriate replacement parts ?

hi, I installed two of the 81-249 rollers today in my Pella sliding door (installed new in 1977). The old rollers came out easily and the new ones were installed without issues. On inspection, the new rollers did not appear to retract into the door as far as the old ones. The roller frame is in as ... (cont.)

I have an older Pella wood sliding glass patio door that needs the roller assemblies replaced. Please provide price and availability for the following roller assemblies that Pella customer service identified for me: Pella part 0C5Y0000 (galvanized) Pella part 0C8P0001 (stainless steel) ... (cont.)

Looking to see if you carry these patio door rollers. I saw that on your website there is a similar product, product #81-098 but the original ones on the patio door have a metal lip that bends to the bottom of the door plate? Does that matter. Thank you