Viewing all customer Discussions for:

23-112 Spring Loaded Top Pivot

Hello, I believe I have a bi-fold closet door with Swisco hardware. It has a square/rectangular door guide cap (on top-see photo) which leads me to believe it is Swisco. Anyway, I have one door where the bottom pivot has been riding in the metal part of the bottom pivot bracket for years possibly a ... (cont.)

Hi there, I can't seem to find replacement pivots for an old steel mirror bi-folding closet. The base is 7/16 but my track opening is 3/8, which means the nylon has to be somewhat smaller.

I need another kit like this

Hi, We are in need of six new pivot blocks for the corner block pins . I think our corner block pins are in good condition wasn't sure if there should be spikes at the top or if we are missing a part could you please look at photos and give us an opinion. Might as well throw in six plastic roll ... (cont.)

Hi there -- What are the pins that goes inside (or compatible with) the corner block? We need to replace the block and the pins. Thanks you!

We have a 36" track which is 1" wide needs replaced since it is somewhat bent. We also need the following hardware replaced. Please advise on what to order. 1. Track 2. Hinges 3. Roller 4. Top mount 5. Bottom mount

Are there replacement parts for the internal bifold door frame brackets that house the pins. It appears these brackets are removable due to the philips head screws. The bifold door pins have worn out the plastic pin housing brackets causing the bifolds to sag when the bifold doors are in the open po ... (cont.)

I have about nine ACME folding doors in a home we just purchased in FL. They are all in varying states of operation and all apparently due to the missing peices of hardware. I took photos of the one that does indeed work, see attached, in the hopes that you could identify replacement parts for me. T ... (cont.)

We inherited a bifold door with all the wrong hardware. I found your item 23-214 2-wheeled roller and it works perfectly with the track. What I didn't order was the additional part needed to hold the fixed end of the bifold door in place. Standard hardware stores only carry something too narrow (se ... (cont.)

I am looking for replacement parts for a Stanley Mirrored bi-fold closet door. I need the floor channel and the four roller assemblies that fit in the corners of the inside of the doors. Channel is 24 inches long, 1 inch high and 1 inch wide. Roller assemblies have the number 4405-R . Please h ... (cont.)

We have two sets of 36 X 80 mirror bifold doors. Doors and mirrors are in good shape but the hardware and tracks are worn out and noisy. I would like to retrofit the hardware and tracks. I have attached several photos. The corner blocks seem to be OK?Can we purchase replacement parts from your co ... (cont.)

Don't know what parts to get. The door won't go on the track. See top and bottom of door and door has some missing pins.

The track in my door is damaged. I need a replacement and I'm having trouble finding a 32" track.

The gray screw keeps coming out of my track and the roller. Help

I Have an ACME 17-4405 block like the picture above which Needs a spring loaded pin and also a broken glide in the bottom of the door track #17-4466. I hope you can help or point me in the right direction. Thanks Jerry

Looking for help with bifold hardware need the top assembly spring mechanism along with pin that goes in the door as well as the pin that goes in the bottom of the door that goes in the track. Pictures attached. Thanks

Upper and lower pivots for two stanley 24 inch mirrored doors. They are separate, not set up as a 48 inch door. Has upper and lower tracks. I need all the pivot hardware to fit in the plastic corner blocks to adjust them to open and close properly.

I have bi-fold beveled mirror glass door for closet, seems heavy, what I want is actually plastic glide which slides in the top and bottom track to run the pivot pin in the track. The pivot pin holder is mounted on the door frame, where pivot pin slides in has the part no. 17-4405, about 18-19 yrs. ... (cont.)

2 each Stanley No. 4425 Wheel for Stanley Monarch Accent 221/Prism 321 door assembly

I am looking for the round plastic piece that rides on the bottom track of the door. In the pictures you can see what the complete one looks like and then the other that is broken. The piece mounts with round lip at the bottom and the shaft on top.