Viewing all customer Discussions for:

23-115 Spring Loaded Top Pivot

I understand that acme 17 -4405 has been discontinued. Here are photos of a 48" and 30" inch set of mirrored bifold doors to repair. I believe I could use 3 screw driver bottom 21-092 6 pivot blocks 23-181 3 bottom drivers with rollers Am I missing any hardware that you might see from t ... (cont.)

I'm trying to replace the crack wheels for my bi-fold doors. Thank you

The closet door is 20 years old. The only label on it says Sunshine Mirror. No part number or any other info just that it meets safety standards. The last photo shows the back or inside of the door. It was mounted in the bottom right corner. I'd really appreciate any help you can give me. Thanks, T ... (cont.)

The plastic guide that fits in the rail, that the door peg sticks into, has broken. I can't find where to get a replacement. I'm not sure the age of the door or the manufacturer. The label is partly covered (see photo). Do you know if the part is still available anywhere? Thanks. ... (cont.)

These doors are approx 15 years old. Should the one top pin have a plastic bushing that slides in the track?

Dear Paul: In these bifold mirror doors, I'm missing several parts. The sticker on the back says Arch Mirror and the track measures 1 3/16 " X 3/4" measured outside.Please advise if you carry the parts like pivot bracket, roll guide, corner connector, pivot pin, screw driver bottom pivot that would ... (cont.)

Hello! I have bifold doors installed, but want to replace the track with the brown one (23-450). I plan to re-use the bottom hardware. For the top part of the door, I assume I should get new hardware from you. Is my understanding correct, that along with the track 23-450 I'd need a top pivot guide ... (cont.)

I got a set of bi-fold doors from a garage sale and I'm looking for the track for top and bottom and whatever other pieces that I may be missing I don't have any to look at to see what parts I missing can you help?

The bottom pin slides into the plastic housing. The doors are mirror bi-folds.

Don't know what parts to get. The door won't go on the track. See top and bottom of door and door has some missing pins.

Door says Sunshine Mirrors. Plastic on pin piece broke, replacement parts found in store are too small of a diameter(shown for comparison in 3rd pic.

I'm trying to re- install 3 sets of Cox bi-fold doors in my daughter's house. She was left with the doors and complete top tracks (I think). The hardware in the tracks is stamped with 43-051. He are pics of the top & bottom of the doors and what was left on the tracks. Any help with the install proc ... (cont.)

I bought a 36" x 80" Gardner bifold mirror door for my closet around 2011. The track pins-parts (as shown in the photo) have broken. Hinge side is fine. Bifold center pivots are fine. But the outer pins on both the upper and lower have left the nylon guide wheels and just won't stay in place if I tr ... (cont.)

I have a mirrored Stanley Bifold door and the bottom nylon roller disk is broken. Where can I get one. The bottom assembly says 4405-R. Joel

Hi Swisco!I have found most of the parts I needed, the 23-115 top pivots and the 23-120 roller wheels .... but, my bottom pivots are different than the ones I see you have pictured.I hope you have the part or its equivalent so I can redo all the closet mirrored doors in my condo ... have lots!I have ... (cont.)

Thanks for responding to my question. The pins currently in the door are 7/16" in diameter at the bottom, and the collar is 1 3/8" long, so your suggested 23-118 part is too small. I think that the problem with the door is less the pins, and more the roller/washer plastic bit that slides back-and- ... (cont.)

I need this bottom door pivot...

Hi I'm looking for 4 of the nylon guide wheels that run in the track. Hopefully you can help me with this. Also 4 of the spring loaded "pins" that push fit into the top and bottom of the doors

the part I need is the little nylon cap on the right end. The diameter of the wider end is 1/2 inch and the diameter of the hole for the pin is 1/4 inch. Pls let me know if you need anything more.

My house in the Netherlands was built 40 years ago and now I can not find spare parts for the tracks of the wood folding closet doors. On your website I found some parts which will probably do, but I am not sure. I herewith send you a picture. I need 2 top pivot brackets nr 43-051 and 2 pins ... (cont.)