Viewing all customer Discussions for:

70-204 Slip-On Latch With Ball Head Screw

I'm looking for replacement (plastic) screen tabs for my removable window screens. I would need approx. 30 tabs (two for each screen) I have attached photos. Please let me know.

Good Morning, My house is approximately 50 years old. We still have our original Pella windows, and they are in good condition. We recently had our house aluminum sided. Although instructed to go around the outside hardware, the contractor removed all of our screen stops on the outside. Pella no lon ... (cont.)

I recently ordered what I thought was the correct Malta window screen clip, 70-048. upon arrival, they were not what I needed, so, I returned them, I was told to send a picture of what I needed, so, attached is a picture of the Malta window screen clip that I need. I was inquiring to see if you carr ... (cont.)

I have aluminum clad Marvin double hung windows that have a removable aluminum framed screen. The screen is held in place by a channel at the top of the window frame and with a pin on either side that fits into a hole in the window frame. I've used your 70-009 pins to replace the pins in the screens ... (cont.)

Your video shows replacing the latch and screen at the same time. But as my screens do not replacing is it possible to just replace the latch? If so, How? Thanks.

Hello - I have Malta windows and on many of them the plastic screen clips are broken. I ordered part 70-048 but the clips didn't fit properly. It fit in the window frame but wouldn't clip into the screen. So now I'm looking for an alternate option. It looks like 70-204 might be a good alterna ... (cont.)

See picture for special screen spring

Hi I'm looking to replace broken vinyl screen track on my vinyl replacement windows. The track is used to hold the screens in place outside of the double hung windows. This track is removable but I can't find a replacement anywhere. Any help with helping to identify this track would be greatly appr ... (cont.)

Your 70-048 clips appears to be suitable replacements for broken ones on my old Malta screens. Before buying some, however, I'd like to get your opinion on whether or not there are other types of screen latches available that would fit Malta screens, perhaps something made of aluminum or that attac ... (cont.)

I'd like to try to replace the broken plunger pins on my Marvin screen windows. Before I order them, do you have a guide to help me? I'll need about 100 plunger pins. Jerry

Hello I've posted a composite picture of what I'm looking for 1) Screen Clips for our sunroom. I think they are your part 70-028. I would also need the small metal screws . 2) Knife Latches (both right and left) for Andersen Storm Windows. I checked with a local Hardware store and they said thes ... (cont.)

The pictures are from a Thermal Gard window. The item snaps/slides into place and holds the Window Screen in place. There is no markings on this piece. Hope you can help. It's getting hot and can not open my windows!!!! Lol...

I can't find them anywhere! Been on the internet, window repair places, dealers, screen repair shops. no one has seen a clip shaped like this. The red colored tip clips into the frame of the window. Any suggestions? Thanks Paul

In the video, the spline would face outward toward the sun. I think the spline should always face inward. If that is correct how would you install these? Or would you need use the pull rings that slip on? Thanks

Slip-On Latch With Ball Head Screw Product Code: 70-204 does this fit a 3/8 screen. jimbo

Could you please confirm the size of the screen bail latch. Is it 7/16 inch wide by 1-1/4 inch long, with the screw set 1" in?

I'm looking for a 1 inch ball head screw from point to end of the ball, with the ball diameter of 1/4 inch. What is the total lenght of the ball head screw? What is the diameter? Thanks, Dave

My window screens are approx 30" wide x 60" tall. How many of the 70-204 latches per screen would you recommend?

I need a side-mounted (vertical)screen pull to replace the plastic pull tabs that came with the Harvey windows.Can I mount your 70-204 vertically? I presume that pressure will keep it in place, right?

I do not need the screws that come with the 70-204 slip-on pull. Is the pull available without the screws? If yes, what's the part number and unit price?Thanks!