Viewing all customer Discussions for:

15-195 1-1/4" T-Lock Balance Shoe, Closed Cam

I'm looking 1-1/4" T-LOCK BALANCE SHOE which is like your Product Code: 15-195, but it has an OPEN CAM. My part also has the white puck.

Does any one can help me find this parts for my double hung replacement windows. Thanks

I am searching for a Series 747 Tilt shoe (1 1/4 x 17/32). The one I have is a closed cam with a metal spring (see attached picture). I can not find a Series 747 tilt shoe anywhere and I was hope you could find one or a suitable replacement. I had purchased replacement in the past, but the company ... (cont.)

Do you sell this type of replacement part? From what I can tell it's a 1 1/4 pivot lock shoe. Thank you.

I have a window balance stamped 33G BSI TK. Looks like rust at the bottom and plastic pieces broke off so I have no way of reproducing what those parts should look like. The builder tells me that the windows were MW industries Patriot series. The "DO NOT REMOVE" label itself shows 84 lmbr and store ... (cont.)

Hello, I am trying to find a replacement for this type of shoe. The window was made in October 2007 by Gulf and Basco. The shoes have snapped off where they attach to the channel balance. I greatly appreciate your help. Thank you Kriss

The windows were replaced a few years ago by the previous owner, and in doing an addition project at our home, the contractor relocated several windows. One window has two busted pivot shoes, one in the rear track and one in the front track. Both are busted out slightly differently, and the only t ... (cont.)

Trying to replace channel balances in double hung windows. Existing spring balance is DSI 22C TO. The plastic piece that inserts into the base of the channel that holds the round metal piece (that secures the window brackets). Also the window brackets are spring loaded. Not sure what the procedu ... (cont.)

The part is T-shaped with three (3) distinct components; the plastic T-shaped block shoe, the metal pivot and a plastic piece that appears to function as a brake for the pivot as it looks like it squeezes against the pivot when inserted into the window slide track.

I believe that I have identified the needed balance as a 32" 795, closed cam, 1.25" T-lock shoe. I will order both the shoes separately and also some complete channel balances. My question is whether the fact that the end of the channel on the ones in place currently affects using the 795 as a repl ... (cont.)

33 lb BFS window sash. The channels are B.S.I. 27D and measure 9/16 wide and 9/16 wide - 27" long. Has the 4610108 patent mark on the bottom connector. this connector mates to the bottom "hook" on the window sash. Need replacement pulleys and bottom connectors - and the channel itself. ... (cont.)

I am trying to replace (8) pivot lock shoes which have a curved C on top that attaches directly to the side of each window spring. I have enclosed (2) photos.

these are metal/Springs about half an inch thick or five eights there are 32 inches tall and I've got plastic parts inside of them I just want to buy the whole spring and hook it back up

The sash pivot is from an Atrium series 150 vinyl single hung window. Any help is most appreciated. Bill

it's 33" long

I have four of these that the sash will not stay up on. The plastic sash pivot piece is broken on two and I cannot find this part. Thanks for your help.

Good afternoon: I need at about 12 of these T pivot shoes, but I did not see the size on your site. Do you have them and how much are they?

Can you help me find two parts for my window. Image is attached thanks

Here's a picture of a part from the side of my Patriot window. It is the same size as the one picture you sent 15-195 but it does not look like the picture you sent. My handyman said a small piece broke off of the end. There are tiny numbers in the piece. They are _AT #S 6.679.000 ... (cont.)

Bought these windows about 15 years ago,AWS company,they're out of business, can't find parts. Balance. 17" long,pivot lock is an inch across, 2 inches long