Viewing all customer Discussions for:

S385-15 15" Series 385 Channel Balance

Hello! I need the part that goes on the other side of the piece pictured. It says DW instead of EW. The length of the metal portion is 15", and it is 1/2" wide.

Don't know the window's manufacturer, but it was likely purchased at Home Depot or Lowes. Metal balance channel width: 1/2" Metal balance channel length: 15" top balance fittings: has wings bottom balance fitting heal to toe measurement: 1 3/32" balance channel stamp code: 14 4 DS CAL ... (cont.)

1440K engraved on the side. I have 3 windows that all need these balancers. I'm looking for the actual part so that I can order and try to fix my windows.

15"

I'm looking for a replacement part for my upward sliding window, sash balance 15 inch. Stamp # 1430Luan

I need 2 replacement Calwell 14 4 BQ Balances. Can you help me get the correct ones?

Please provide link to the balancer shown. The window is a small bathroom window, not more than 6 pounds. Its metal channel is 15 inches and there are no stamped numbers I could find. Also need a couple new side clips that capture the upper plastic fitteng. The ones installed are severely rusted. Th ... (cont.)

The metal length is 15 inches. I can not find the name. I need two of it.

Need help to identify channel non-tilt balancer...Metal channel size is 15"Channel width is 1/2"Stamp "14-3 GD5 CMC 87"Sash weight is 7.5 lbs.Thanks,Francisco

Hello, I sent a previous request. This is another size balancer I need help identifying the correct replacement item. It measures 15in long and 5/8 wide. Marking is 14 5 HW CMC 7. Please let me know if you need any additional information to assist me in identifying the correct replacement part. Than ... (cont.)

Metal length 15 inches. Marked with "14 5 CW CMC 10".

Need 2 new channel balance to match this. Weight of window is 25.5 lb

Here are some measurements that I took. Hopefully these make some sense as I have not worked with windows before. I wish I had the old balances so that I could measure them but the previous owner apparently threw them out :-(Length of channel in the moving part of the window: 16 3/4"Depth of channel ... (cont.)

Channel Balance is 15" long and 1/2" wide Stamped with 14-2 Window weighs 11.5 pounds and hoping to go up to 14-3 because windows are sagging with the 14-2. Looks like 15" Series 380 Channel Balances and just wanted to double check with the pros before ordering 4 of them to replace balances for 2 id ... (cont.)

Hello, I have a window channel balance with a broken string. The partner balance string is also damaged and requires replacement. The number on the balance is 14-4 FD5 CMC 45. The metal portion is 15" long x 5/8" wide x 5/8" deep. Thank you, Norman

Needing a pair of these balancers. The nylon cord broke on the one. Any help would be appreciated.

Photo shows the part and plastic ends. Roughly 15" channel.

Channel Balance 15 inch # 14-2 EGR CMC 54 Window # 144-992324 23 1/2 x 35 1/2 Series A571 single hung Thanks I am just a retired Commercial Electrician But you video makes it very easy Darrel

Cord broke on one on my Channel Balance. I am looking to replace The pair. Marking on side shows, 14 3 LR CALDWELL.

I'm sending you two emails (and two sets of photos) because I need to order channel balances for two different sizes of windows. This second set of five photos is for the smaller windows (3' by 3'.) The metal part on these balances measures 15" long, and they are marked 1440 BSI RO.I think that mean ... (cont.)