Viewing all customer Discussions for:

26-083 Pivot Bar, 2-1/2"

Please help me Identify these Pivot Bar attach brackets? Thank you,Roland

I require the male window connector piece to the window frame. The photo shows an intact piece. I have 2 windows were these pieces rusted off.

Hello This is the underside of my window and this little piece of metal sticks out and latches into the spiral balance unit. The other side is missing so I need another. What is this part called? Thank you!

I've got a couple old vinyl windows that I can only guess are just warped or worn because the 2.5" pivot bar ( 26-083) just keeps popping out. I replaced every single pivot shoe and bar on one window, and within a few ups and downs one side or both pops out.. Both sashes have this problem. I wa ... (cont.)

Hi. I'd like to replace the pivot bar on a few of these windows. The entire mechanism seems to have deteriorated due to weather exposure.

Hi, I need 8 pivot pins for a tilt out window. Length is 2 1/2" x 1/4" wide x 3/16" deep We bought and received the channel balance boots 'C' last week, Thank you.

I have noticed that all my upper sashes use the 26-412 cast pivit bar and the lower sashes use 26-040 steel pivit bars. many of the upper bars have broken when I have taken the windows out. Is there a "steel" replacement picit bar I can use that would have the same screw hole spacing as my 26-412 c ... (cont.)

31 windows in my house with year round salt air exposure leads to a lot of rust and corrosion. Was hoping I could replace a number of these that have given out. Not sure of the window brand. Maybe DACO? Any help would be appreciated.

Hello Can you help with this coil balance? I have included other parts that i have identified, in case they help.

I need pins to fit into the slots one for each side

I need 1 or more of these. I've seen in your list the 3" with 3 threes. This is a JeldWen Premium Atlantic Vinyl Single Hung Window. This however has only 2 holes.

Hello,I looked at your website and I think I need the pivot shoe 15-111. My problem is that I can't seem to find a matching pivot bar on your website. My pivot bar is 2.5 inches long with small diameter holes at 1.5 and 2 inches. Thank you.Jeff

Hello you were very helpful in identifying and ordering replacement tilt bars. However, now I'm unable to remove the corroded remaining pieces. My window installer tells me that a tilt bar holder assembly needs to be replaced. Are you able to help point me in a general direction.Thank youScott ... (cont.)

Hello, can you please tell me if available what i halve circled around?

Hello, Many of my Pivot Bars have rusted out and broken off. I think most of my Pivot Shoes are okay - if I can get the rusted pivot bars out of them. These are Concord Vinyl Windows, by Alcan Building Products, installed in my home in January 1996. I have more photos to send you but I've reache ... (cont.)

I have the same windows Polytex DH 3000. Need help finding the aluminum guide pin located in the bottom of the top windown.

Need that u-shaped metal piece that goes into balancers

A customer's sunroom has 6 double hung windows all with broken aluminum pins similar to your #26-412. The number cast into the original part is "1074". Im looking to see if there is a steel replacement. Thanks.

Hi, I have a Home Depot 8501E Window - This was mounted in a bathroom shower, and the pivot lock shoe mechanisms and lower window sash "pivot tabs" on the lower corners of the sash have rusted away. Can you help me find replacement parts? This balance mechanism seems to be a "tape" of some sort sec ... (cont.)

I recently ordered 12 pivot bars (26-083). All dimensions are perfect EXCEPT the width. Looks like the width I need is 1/4", not 5/16". If you had one the same dimensions but only 1/4" wide, it would be perfect. The whole length has to be 1/4" because it slides into a bracket. Do you have those? ... (cont.)