Viewing all customer Discussions for:

89-029 Viking Keeper

Hello, We have this pella sliding door that is missing the keeper. Unable to find it. In Pella's website iit is referenced as V615275 (w), or V615277 (A). Do you think the part that we need is the 89-039 or 89-029 ? Thank you very much! Joe

I am looking for the lock to this glass door. Nami Code: ALS Rating: SGD Series: 170 MST: 80610

Need whole set

hello I am looking for the keeper to a 6700 7700 series eco view sliding glass door. It looks like it could be your 89-029 or 89-041

Hi, I just moved into a condo and recently discovered the piece where the latch should hook into is missing. Pic where there is 4 screw holes. The label on the jamb says SGD-LC25-96x96 AND SGD-C30-96x82. If you could help me out or direct me in the right direction I would appreciate it. Thank you. ... (cont.)

Need 2 parts - see attached. Part numbers are: OC3M000 and 0C3P6000

please see the picture. All on the pictures are OK. I just need lost all the parts on the door frame.

Hello Please find the attached file. Please suggest me that which mortise lock I need which fit perfectly in to my sliding glass door based on the dimensions. Thanks Rajesh Sash Controls Ferndale MI 2260 Taiwan U.S. Patent 5125703 D340398

Hi there, I am selling my condo and the buyers want a latch that doesn't require undue finesse to lock. The label on the jamb says SGD-LC25-96x96 AND SGD-C30-96x82. (Images attached). Can you direct me to the appropriate replacement handle and latch set I need? Thanks!

My Patio door closes just fine and the alignment "seems" good, but it must not be because the latch bumps the keeper when I try to close the latch. Then it doesn't fully extend and latch. The workaround is to start with the latch extended and down, (lever halfway) and finish it off after closing. Gu ... (cont.)

I have both the handles (inside and outside.I need the hardware for inside, between handles with the latch behind the handle on the inside and the latch on runner to latch on the hook from the handles., missing when we purchased the home last month. Measurements for sliding glass door lock- 7 3/8 lo ... (cont.)

I have a 5 ft pella vinyl door that is missing the keeper. I was wondering if you could identify which part might work so I can order it, thanks- Garrett

Hello! I have seen several queries about the Series 870 patio door mechanism, presumably an old Philips door, originally marketed for manufactured homes. As far as I can tell, my question is unique- which is, I am looking for the latch/lock plate that goes in the door jamb area. A while ago, I purch ... (cont.)

Hi, do you have something that would work for me? It's a keeper for a Pella sliding glass door.

Existing sliding door series: Summit 8670, SGD-C20 does not have a keeper. Apparently removed by previous owner. Can you please tell me what keeper model I need. Thank you.

Hi - I have a Windsor Next Dimension sliding patio door and need to replace the plate that holds the latch. Two pics attached. Can you direct me? Thanks!

After I removed the 'keeper' part of the sliding door lock I misplaced it and can't find it again. What part exactly do I need and do you carry it? Thanks!

My patio sliding door lock is broken. I need to replace it. I see some code as 16 CFR 120 11

Door is 71.5" W x 79.5" H. Markings indicate model SGD-R20 series 800. Several screw holes appear where the latch once was, but I'm not sure which are from the original latch. The eye bolt works ok, but I want to find the original equipment.

Hi! I have a door that is missing the plate for the latch to hold locked. Door says Series 890 AAMA/NWWDA 101/I.S. 2-97 SGD-R15-120X96 SGD-R20-120X82 Please direct me to the needed part, thanks!