Viewing all customer Discussions for:

81-266 1-1/4" dia Roller And Axle Kit

I see that the roller 81-013 is discontinued, what roller# is a replacement for it.

need a pair of these for an oversized patio sliding door. Probably should have taken more photos, let me know if you need more info. The door is cross town at my daughter's house so it would be a couple of days before I can take it apart again.

Sliding glass door rollers. Please help me order these

Hello Swisco!I have an old sliding glass door (possibly 1970s?) that has gotten a little "gritty" with its sliding operation. I took it off of the track, and discovered that the wheel has broken. However, I was hopeful when I saw that the whole wheel module was easily removable.We've looked at our ... (cont.)

Hello. The dimensions of existing wheel assy. are: 1" wheel, 1/4" wide; mount bracket is 5/16" wide, 1/2" tall at tallest point, 2 1/8" mount hole spacing ( 1 1/16" from either side of adjusting screw. Purchased 84-074B and the diameter of the wheel was too small then purchased 81-266 and the whee ... (cont.)

Please help identify rollers for this door. Wheel is 1.0" (in groove) and 1.23" max dia. Roller bracket is 2.4" long, 1.23" tall, and 0.73" wide (max at top) 0.56" wide (min at bottom). Tab sticking out dimension is 1.46" (from bottom of roller bracket to top of tab). Hole to hole dimension is 0.8" ... (cont.)

My name is Michael, want to know if the part is available. If not, can I just replace the wheels? If so, is there wheel parts and tool to take the wheels off? Thank you so much for you soonest advise on what options are there for me.

I would like to replace the rollers on my mirrored closet doors (2). They are approximately 30 years old. I will upload a couple more photos in a second email.

Please let me know what roller will work for this replacement. It is 1 inch wide. The wheel is 1 1/2 wide. The frame is 2 3/8 long. Is it possible to get a replacement wheel?Thank you,Audrey

I am looking for such wheels

I need to replace my sliding glass door rollers. Pictures of the old rollers are attached. I think this door was installed in 1999 and I thought it was made by Traco, but I'm not sure of that anymore.

My adjuster wheel came apart

Hello, I would like to know how if you carry this item and how much it would be. I would need 2.

Both sets of rollers are shot and do not spin. I cannot locate any part numbers. The roller is 4 1/2 inches long and 1 1/4 tall and 5/8wide. The roller is pressed into a plastic piece that presses into the door. The code on the door states: code- TEI Rating- SDG-r40 Series- opera patio door MST- 51 ... (cont.)

I need to replace the roller for what I suspect to be a 1973 era sliding door. Previously, I purchased a couple rollers, however, they were not correct as the location of the height adjustment screw and the frame attachment were incorrect. As a last resort, replacing just the wheel will suffice. ... (cont.)

Hello, I'm in need of 2 new rollers for my aluminum sliding door. I was able to remove the wheels but have had no luck in replacing them and I hope you can help. The door is old, a little over 6 feet tall with a single sliding glass.The roller itself is approx. 1 3/8" tall (to the tang). 1/2" wide w ... (cont.)

Are you able to recommend a replacement solution?

Seems to be a brand X door. Sorry, my son thought it would be fun to take them apart and bend them all up. There are two of them on the door. There are no marking on the part or the door that we can find. Please help!

The rollers for our sliding glass door need to be replaced, but I have no idea how or if it can be done. There are no identification marks on the door itself and the rollers are attached to a single , track-like assembly that screws directly into the bottom of the door as one unit. Any help identi ... (cont.)

We purchased the door from Lowe's and I believe it is a Reliabilt. One wheel has collapsed because its bearing has broken. The case measures 4.5" x 1 5/8". There are two screw holes on the top of the case. I apologise that I did not photograph the door with the roller assembly installed but I ... (cont.)