Viewing all customer Discussions for:

26-405 Rounded End Pivot Bar, 2-7/8"

This part broke that is on the inside of the window alley where the window goes up and down. I think it allows the window to be tilted.

Hello, I have some Accuweld 2600 Silver Series windows with broken pivots in the coil balance shoe assembly. I have attached a photo, and it is the round pot metal piece where the pivot pin fits into. The number on the assembly is 7. Are these available? if so, can you provide the cost, please? ... (cont.)

Discontinued window. Looking for new balance. Don't have manufacturer.

The springs on my coil balancers are breaking about every 6 months or less. The windows are from Hurd and no longer manufactured.The original shoe ears break off often. The spring bends and breaks where the 2 springs join. The spring mounts on the rotating shaft with a rubber gasket. The shaft turns ... (cont.)

I have replacement windows in my home that were put in prior to my purchase. One of the single hung windows had the shoe piece of the balance crack and break on both sides.I have contacted local window repair shops to be told that the parts are no longer made. I am hoping you can look at the attache ... (cont.)

Hi, My vinyl window was difficult to shut and when I got it shut the part on the side broke

This balance came from an Anlin single hung window. The measurement of the sash is 40 x 27 inches. The only markings found on the balance are (7+7) Not sure what they mean. The measurements of the part are 9/16 and 1 1/4. Just like the ones in your images. I am also going to need the pivot bar wh ... (cont.)

Hello, I bought the S140-13 Quick Tilt Balance thinking it would be a drop in replacement/upgrade for my broken coil balance. So far it seems the width and depth are about right (haven't fully tested the fit yet). Unfortunately when I tested the fit of the sash pivot, the S140 shoe is just a ... (cont.)

Hello, First of all, I love your website! I have a SWC double-hung vinyl window. Looking for the following parts: The window is H-52", W-35" 1- The metal pin that is attached to the bottom of the window and slides into each side of the plastic holder that is attached to the balancer. ... (cont.)

Please help identify this pivot bar

I purchased the S140-11. However, my pivot bars dont fit.My pivot bar is 26-226. But, I need the complete coil balance and shoe as I the old ones are shot.

could you show me correct pin that will fit this new hardware,

I ordered these several years ago and now cant find them. Do you have something that will replace these

Please see images of pivot bar and broken latch Can you help identify the parts for me? I need 2 pivot bars and 1 latch

We have two "Certainteed" windows that go up and down to open and have broken parts that need replacing. We have attached two pictures to show the broken parts. We would like the entire assembly replaced.

parts are out of window at Valleybrook in Blackwood (La Coasta). Coils are #7, two per shoe, and slide into shoe.

I need to replace the coils counterbalance for about 4 sashes. The window sash weighs about 19 lbs on my floor scale. It looks like a dual coil system. The coil is about 1/2 inch wide, there is a DL6 printed on the lower coil and just a D6 on the other.

I am looking for windows Balance mechanism and Pivot Bar for my Milgard window. It looks like your site is not able to except another pictures.("add another image" does not work) Could you please help me identify the part number which I need to purchase. The broken Pivot Bar total length is about ... (cont.)

I have a vinyl window (unknown manufacturer) and the channel balances have failed. I need a replacement part. Can anyone recommend a replacement part? Thanks,

I am fixing a customers window. It has triple coil balances. I already ordered the carrier setup, and I can't figure out how to get all three coils attached to the bracket. After research I came across the same question answered on your site. I have given up on using the original setup, and I am goi ... (cont.)