Viewing all customer Discussions for:

21-174 Roll Guide

Hi, We are in need of six new pivot blocks for the corner block pins . I think our corner block pins are in good condition wasn't sure if there should be spikes at the top or if we are missing a part could you please look at photos and give us an opinion. Might as well throw in six plastic roll ... (cont.)

I need button-like plastic sliders for old circa 1984 mirrored bifold closet doors.

Is a small part that is inside the channel and makes the door slide

I have a bifold mirrored door whose bottom track has a plastic piece that slides back and forth in a grove in the bottom track to support and "guide the moving side of the bifold door. The plastic sliding piece is installed in the track prior to settin the bottom track in place. This plastic piece i ... (cont.)

These pictures correspond to a Stanley 36" Bi-Fold mirror door. I used 2 for my closet. The guide wheel broke on the bottom left and my adjustment and my bottom pivot that adjust doesn't adjust now! All the guides and pivots fit in Stanley #4405-R if that helps. I could us one bottom track, 2 new gu ... (cont.)

I understand that acme 17 -4405 has been discontinued. Here are photos of a 48" and 30" inch set of mirrored bifold doors to repair. I believe I could use 3 screw driver bottom 21-092 6 pivot blocks 23-181 3 bottom drivers with rollers Am I missing any hardware that you might see from t ... (cont.)

Are there replacement parts for the internal bifold door frame brackets that house the pins. It appears these brackets are removable due to the philips head screws. The bifold door pins have worn out the plastic pin housing brackets causing the bifolds to sag when the bifold doors are in the open po ... (cont.)

this piece in my hand to 36'' x 80'' mirror door

I'm trying to replace the crack wheels for my bi-fold doors. Thank you

Have not been able to find an identical part. I have purchased ones that look very close from the website but we're either too short or not wide enough to stay in the track. For a metal bi-fold/mirrored closet door.

The plastic guide that fits in the rail, that the door peg sticks into, has broken. I can't find where to get a replacement. I'm not sure the age of the door or the manufacturer. The label is partly covered (see photo). Do you know if the part is still available anywhere? Thanks. ... (cont.)

These doors are approx 15 years old. Should the one top pin have a plastic bushing that slides in the track?

I have an older Glass Bi-fold closet door. The guide pin is binding on the track because the guide roller broke. The spring stop also broke. The only part number I could find on the closet door is the Acme 17-4405 corner block. My condo apartment was built around 1980. Thank you. ... (cont.)

Where can I purchase

Hi there, I am trying to locate the small plastic rectangular piece inside the track of the rolling stanley/monarch mirror closet door. It has a circular piece int he middle that a cylinder metal part from the top and bottom of the mirrored doors slots into but they are very worn down and some are ... (cont.)

Dear Paul: In these bifold mirror doors, I'm missing several parts. The sticker on the back says Arch Mirror and the track measures 1 3/16 " X 3/4" measured outside.Please advise if you carry the parts like pivot bracket, roll guide, corner connector, pivot pin, screw driver bottom pivot that would ... (cont.)

Hello, Attached please find the inside corner piece for our bifold mirror Closet doors. The door corner piece holds the door together on the inside and keeps the mirror piece inside of the frame. It is one of four inside corner pieces on the inside top of the bifold door. Ours is cracked and we ca ... (cont.)

I am looking for replacement parts for a Stanley Mirrored bi-fold closet door. I need the floor channel and the four roller assemblies that fit in the corners of the inside of the doors. Channel is 24 inches long, 1 inch high and 1 inch wide. Roller assemblies have the number 4405-R . Please h ... (cont.)

We have two sets of 36 X 80 mirror bifold doors. Doors and mirrors are in good shape but the hardware and tracks are worn out and noisy. I would like to retrofit the hardware and tracks. I have attached several photos. The corner blocks seem to be OK?Can we purchase replacement parts from your co ... (cont.)

I have enclosed , via attachment, photos of the two needed parts. I also provided you some measurements and descriptions of these items. They are as follows: 1, DISK (Function: A "push pin "apparently seats inside, this disk, while it rolls/slides along inside the tracks. The dimension ... (cont.)