Viewing all customer Discussions for:

21-174 Roll Guide

I am looking for replacement parts for a Stanley Mirrored bi-fold closet door. I need the floor channel and the four roller assemblies that fit in the corners of the inside of the doors. Channel is 24 inches long, 1 inch high and 1 inch wide. Roller assemblies have the number 4405-R . Please h ... (cont.)

We have two sets of 36 X 80 mirror bifold doors. Doors and mirrors are in good shape but the hardware and tracks are worn out and noisy. I would like to retrofit the hardware and tracks. I have attached several photos. The corner blocks seem to be OK?Can we purchase replacement parts from your co ... (cont.)

I have enclosed , via attachment, photos of the two needed parts. I also provided you some measurements and descriptions of these items. They are as follows: 1, DISK (Function: A "push pin "apparently seats inside, this disk, while it rolls/slides along inside the tracks. The dimension ... (cont.)

The little white plastic piece is broken to hold my mirror and for it to slide when I open or close the closet The sticker Stanly was inside the mirror Would you have a replacement Thanks Neil

I am looking for off white plastic slotted washers 1" in diameter, 1/4" wide used on a sliding mirrored door.

Could you tell me if this plastic part is called "roll guide"? It's on the pin of the bottom track of bifold door. If so how difficult is it to replace? The other door that part broke and door is difficult to close.

Missing the screw type metal bottom guides, I only have one that is in the picture.. need 3 but 4 would be fine. Also 4 to 6(extra) round plastic circle guides will do it! The 4 top spring are still functional!

I need to replace the white plastic guide wheel cap in the attached photo. The cap is circular, about 3/4'' in diameter. This item is part of a bi-fold door made at least 12 years ago by Stanley. The cap sits on top of a guide wheel that slides along a metal track that allows me to open and close ... (cont.)

The gray screw keeps coming out of my track and the roller. Help

I have a 25+ year old mirror glass dual bi-fold door. I'm missing one of the four little round "glides" that go on the ends of the guide pins and ride in slots in the sides of the top and bottom tracks. The logo on the door mounting hardware says "Acme" with the number 17-1405. When I Google that ... (cont.)

I bought a 36" x 80" Gardner bifold mirror door for my closet around 2011. The track pins-parts (as shown in the photo) have broken. Hinge side is fine. Bifold center pivots are fine. But the outer pins on both the upper and lower have left the nylon guide wheels and just won't stay in place if I tr ... (cont.)

I have a mirrored Stanley Bifold door and the bottom nylon roller disk is broken. Where can I get one. The bottom assembly says 4405-R. Joel

Outside diameter of the roller is approximately 7/8". Inside diameter of the center hole is 3/8" where the spring loaded pivot goes into the hole. The height of the roller is 1 /4" . The width of the track is 1" .

Hello Sent a couple of pictures of bi-fold door parts I am looking for. Nylon bushing and snubbers for four door bi-folds. I believe model number of door is 10909991? thank you, Ron

To#ondoor Stanley,51026942 243504

Thanks for responding to my question. The pins currently in the door are 7/16" in diameter at the bottom, and the collar is 1 3/8" long, so your suggested 23-118 part is too small. I think that the problem with the door is less the pins, and more the roller/washer plastic bit that slides back-and- ... (cont.)

Bushing used as a glide in upper track for my bi-fold doors. Manufacturer unknown. ID is 1/4 inch, OD is 3/8 inch. Length is 5/16 inch. Flange OD is 5/8 inch. Flange thickness about 1/32 inch. Most critical measurement is ID and flange OD.

I need this bottom door pivot...

Hi I'm looking for 4 of the nylon guide wheels that run in the track. Hopefully you can help me with this. Also 4 of the spring loaded "pins" that push fit into the top and bottom of the doors

I have bi-fold beveled mirror glass door for closet, seems heavy, what I want is actually plastic glide which slides in the top and bottom track to run the pivot pin in the track. The pivot pin holder is mounted on the door frame, where pivot pin slides in has the part no. 17-4405, about 18-19 yrs. ... (cont.)