Viewing all customer Discussions for:

26-175 CertainTeed Pivot Bar, Pair

Need a pivot bar for double hung window. This one is from the good side, the other side is broken

I have some older certain teed double hung windows i need replacement pivot shoes the code on the existing pivot shoes is A1 87598 is your pivot shoe 15-192 an operable replacement? also will need the bars that screw to the sash and hook into these shoes. Thank you

After washing the window, it evidently was slightly out of alignment and broke I broke the pictured piece while forcing the window closed. What is the part called / part number, is it available, and is it hard to install? Is there a right and left hand? The piece which broke is on the left side w ... (cont.)

Attached, please find pictures of a vinyl window pivot tilt bar with foam roller. I was unable to find these in your online cataloged. Do you have a replacement?

These came from CertainTeed Windows installed in the Turks and Caicos in late 90s or early 2000s. Can you identify and do you stock the part.

Looking for these parts pivot assembly has # A186160 on it, springs have#'s 407 and 408 depending on window. The lance spring cover and balance drum look different tha what I see on your site

Cetainteed window. Corner peice for sash is broken and looking for new one to repair it

trying to identify window sash pivot. I think the windows might be Bryn Mawr series windows from certain teed. Can you help? I would need right and left side for bottom sash. Probably (2) pair. Thanks Joe

I'm sorry but I don't have the broken pieces. I've tried to take photos of every angle that I can without hiring someone to take the window out. It fell when I was washing the upper half when both pegs on the pivot bar broke. I have additional photos and will try to send them via the link provide ... (cont.)

Hi Swisco, I need another part for the same window. The window keeps falling down because the metal tab is broken as you can see. Can you tell me what part number I should order? Thanks, Quinn

I had ordered part number 26-175 : CertainTeed Pivot Bar, Pair but it is too wide at the base and will fit in the channel. picture attached showing the difference in width from original. I did not see anywhere else on your web site for an alternate, as all stated this part would fit, no problem. ... (cont.)

This is a picture of part I need. This is a tilt in, double hung vinyl window. This part is found on each side of the bottom of the window and stabilizes the window in the frame and keeps it in place when the window is tilted in. Thanks for insight or suggestions.

Hello, I have a few CertainTeed windows in my rental property with in various need of repair. 1) One needs a Pivot Bar replacement - it looks as if 26-175 is what I need, though this looks to be a newer style 2) The top section of the window on one will slide down as soon as the window is unloc ... (cont.)

I need a replacement for a Certain-Teed Sash Pivot Bar. Item number 26-353 on your website is basically similar to the broken pivot bar I need to replace, except that the original also has a small 1/8" knob located about 7/16" from the screw hole on the flat surface of the pivot bar and ext ... (cont.)

The window about a 2006.

I believe it is called a certain teed pivot bar. The number on it is 103-2. The pictures I've attached show it broken. I need to replace it. I've ordered one in the past but it was the wrong piece.

I ordered a certianteed pivot as the measurements and general appearence was the same but this one has an offset pivot. Do you think you have something for this?

Hi I am looking for: 2-ea Sash Pivot Bars 4-ea LH Window Latch 6-ea RH Window Latch Regards, Charles

I just purchased a number of S170-405 coiled balance spring. In replacing the springs one of the pivot bars were broken. I attached a photo of the part needed. It basically is a right angle cast aluminum bracket with the large leg 2.5" x 7/8" (outside measurement). 5/8" wide , 1/8" thick. there i ... (cont.)

I'm looking for a pivot bar from an old CertainTeed window from around 2002. I don't have a model number on the window so I attached some pictures of what I need.The first picture shows the bottom of the piece which is 2 5/15" long. The width is 5/8 " and the short side length (second pic) is 7/8" ... (cont.)